Turbosound LMS-D6, LMS-D24, LMS-D26 user manual TA-890

Page 54

user manual

TA-890

Edit Select Buttons – the currently selected edit parameter is displayed on the bottom left corner of the LCD. Pressing the edit select buttons moves through the available parameters for the current input or output.

Text display – preset, channel, parameter and status information is shown on the 2x 24- character text display. In most screens the currently selected channel is displayed on the upper line and the edit parameter on the lower line. To simplify the display and enhance security, some parameters or parameter pages are omitted when not relevant.

Parameter Knobs – three velocity sensitive parameter knobs are used to adjust parameters shown on the display. Up to three parameters are displayed on the screen. The parameter name is shown above the parameter value in each of the three screen sections. The parameter knobs have a fixed association with the screen sections; the rightmost parameter knob adjusts the rightmost parameter and so on.

Output signal and limiter indication – two LED’s are provided for each output channel. These show the signal level relative to the limiter threshold. The yellow LED will light when the signal is 6dB below the threshold and the red warning LED will light when the limiter threshold is reached.

Mute buttons and status LED’s – each output has a mute button and associated mute status LED. Pressing the button toggles the mute on and off.

Note that the mute buttons do not function when the Secure Mode is activated.

Secure Button (on the rear) – a momentary button is fitted behind the rear panel, between the output XLRs and the RS232 port. When activated, this will disable all the front panel controls so they cannot affect the signal path, making the unit secure against tampering. When in secure mode, the indicators still operate normally.

Note that the communications port is still active in secure mode.

TA-890 user manual Page 54

Image 54

Contents Aspect TA-890 System TA-890 TA-890 TA-890 Amplifier Rack Signal Wiring Output Connections EC Declaration of Conformity ProductsIntroduction Turbosound Aspect System ConceptsTurbosound Polyhorn TA-890 Aspect TA-890 Turnkey System Concept LMS-D24, LMS-D26 and LMS-D6 Loudspeaker Management Systems Power AmplifiersLoudspeaker Management System LMS Concept Amplifier RacksDigital Controllers Aspect Loudspeaker ComponentsTA-890L Low Frequency Enclosure TSW-218 Subwoofer TA-890H Mid-high EnclosureTA-890 Transportation Aspect Flying Systems Flying and Stacking OverviewSetting up a Venue Overview Gigmate Acoustic SimulationRunning Turbosound GigMate / Ease Focus for the first time System Setup Designing a system TA-890 TA-890 Changing the system Theatre-style venue 3-wide flown cluster @ 1kHz Safety Notes on Rigging Sample Certificate of Load Test Wide and Narrow Flybar Settings Flying HardwareSingle A-System Flybar FB-890/1A TOP View Bottom View Figue 3. Triple ‘A’ System Flybar FB-890A/3W FC-890 Flying Chains TS-890 Tilting StrapsTA-890 Four-wide hang using MB-890 and FB-890/2A Integral Flying Hardware ‘A’ System FlygearDrop Link Connecting Flying Chains to the CabinetConnecting Cabinets ‘A’ System Swing LatchSetting Vertical Angles ‘A’ System Attaching the Tilt Straps Attach buckleTurbobass Directivity Bass Enclosure arrayingAiming directivity of the stack TA-890 Typical Left to Right problem ABC DEFCreating Directional Bass arrays Bass in a lineFanned bass Bessel Array General observations of long lines of bassEnd firing array Summing up Ground stacking LMS Series Loudspeaker Management Systems General features & facilities UnpackingMechanical Installation IntroductionLMS-D6 Front Panel Functions Mains Power LMS-D6 Rear Panel FunctionsAC Power Fusing Voltage SettingSafety Earthing Powering UpInput and Output Connector Wiring Time correction for loudspeaker driver placementAudio Connections Features LMS-D24 and D26 Loudspeaker Management SystemsFront Panel Functions TA-890 Rear Panel Functions Starting up Selecting a Factory PresetOperating the LMS-D24 and D26 Creating a CrossoverA Freq Width Gain EQ1 100Hz 1.4Q 0.0dB Navigation and Viewing ParametersOut1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB NavigationPreset Recall PresetsPreset Name Store My System Preset StoreDSP Processing Layout Input DSP block diagramOutput DSP block diagram Stereo / Mono FormatsDSP Processing Input ChannelsA Freq Shape HPF 20.0Hz LR24 Parametric Equalisation High and Low shelving filtersParametric filters Delay Output ChannelsGain and Polarity Out1 Freq Shape LPF 2.50k LR24 High and Low Pass FiltersOut1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Limiters RoutingUtilities Utility functionsAudio Input Connectors AMP-890 Aspect System Amplification Rack Racking, Cables and ConnectionsOptions Input ConnectionsAmplifier Rack Signal Wiring Output ConnectionsMid-High Outputs Break-out Cables NL4 bass Break-out cables NL8 mid-high Extension CablesMains Connections T-45 High Efficiency Audio Power Amplifiers General Features & FacilitiesFront Panel Functions T-25 Front Panel Functions T-45 Mechanical Installation Voltage Range Audio Connections & ControlsGain and Sensitivity Settings PolarityInput Impedance Attenuation & Gain Setting Damping FactorLong Speaker Lines Cooling SystemMaintenance To rotate the horn moulding from ‘A’ mode to ‘B’ mode To rotate the horn moulding from ‘B’ mode to ‘A’ mode Removal of the high frequency driverRemoval of the high-mid frequency driver General Maintenance Removal of the low-mid frequency drive unitsPaintwork TA-890 Technical Specifications Warranty Serial NumbersTA-890