Turbosound LMS-D24, LMS-D6, LMS-D26 user manual Rear Panel Functions

Page 55

user manual

TA-890

Rear Panel Functions

	Expansion	Secure Mode
	Port
		Switch	Audio Input
	Power Inlet
			Connectors

Serial Comms

Port

Audio Output

Connectors

Power Inlet – provides connection to a suitable mains electricity supply using the cable supplied. The controller has a switch mode power supply that is capable of operating with a nominal mains voltage of 80 to 240v, 50/60Hz without re-configuration.

Network expansion port – where a future network card can be fitted.

Audio Input connectors – these are fully balanced and are wired pin 1 ground, pin 2 hot and pin 3 cold. The two inputs have pin 1 connected directly to the chassis and feed the signal processing chains. If an unbalanced source is used, a connection should be made between the pin 3 ‘cold’ signal and the ground connection of the unbalanced source.

Audio Output connectors – the processed outputs are impedance balanced, and are wired pin 1 ground, pin 2 hot and pin 3 cold. An unbalanced input may be driven by by connecting pin 3 ‘cold’ signal to the ground connection of the unbalanced destination input. Note that output pin-1’s are ground lifted at audio frequencies but connected to ground at RF for good EMC performance. The intention being that the amplifiers the processor is driving should be responsible for the grounding of their input cable shields.

Communications port connector – the unit may be controlled entirely from another controller (typically a Personal Computer), running an application that is compliant with the ObCom standard. Connection will normally be made to the controller via this serial port connector. This port is also used for updating the firmware in the unit.

Note: The communications port is NOT disabled when the front panel is made secure using the secure button.

TA-890 user manual

Page 55

Image 55

Contents Aspect TA-890 System TA-890 TA-890 TA-890 Amplifier Rack Signal Wiring Output Connections Products EC Declaration of ConformityTurbosound Aspect System Concepts IntroductionTurbosound Polyhorn TA-890 Aspect TA-890 Turnkey System Concept Amplifier Racks Power AmplifiersLoudspeaker Management System LMS Concept LMS-D24, LMS-D26 and LMS-D6 Loudspeaker Management SystemsAspect Loudspeaker Components Digital ControllersTA-890L Low Frequency Enclosure TA-890H Mid-high Enclosure TSW-218 SubwooferTA-890 Transportation Aspect Flying Systems Overview Flying and StackingGigmate Acoustic Simulation Setting up a Venue OverviewRunning Turbosound GigMate / Ease Focus for the first time System Setup Designing a system TA-890 TA-890 Changing the system Theatre-style venue 3-wide flown cluster @ 1kHz Safety Notes on Rigging Sample Certificate of Load Test Flying Hardware Wide and Narrow Flybar SettingsSingle A-System Flybar FB-890/1A TOP View Bottom View Figue 3. Triple ‘A’ System Flybar FB-890A/3W TS-890 Tilting Straps FC-890 Flying ChainsTA-890 Four-wide hang using MB-890 and FB-890/2A ‘A’ System Flygear Integral Flying HardwareSwing Latch Connecting Flying Chains to the CabinetConnecting Cabinets ‘A’ System Drop LinkSetting Vertical Angles ‘A’ System Attach buckle Attaching the Tilt StrapsBass Enclosure arraying Turbobass DirectivityAiming directivity of the stack TA-890 ABC DEF Typical Left to Right problemBass in a line Creating Directional Bass arraysFanned bass General observations of long lines of bass Bessel ArrayEnd firing array Summing up Ground stacking Introduction General features & facilities UnpackingMechanical Installation LMS Series Loudspeaker Management SystemsLMS-D6 Front Panel Functions LMS-D6 Rear Panel Functions Mains PowerPowering Up Voltage SettingSafety Earthing AC Power FusingTime correction for loudspeaker driver placement Input and Output Connector WiringAudio Connections LMS-D24 and D26 Loudspeaker Management Systems FeaturesFront Panel Functions TA-890 Rear Panel Functions Creating a Crossover Selecting a Factory PresetOperating the LMS-D24 and D26 Starting upNavigation and Viewing Parameters A Freq Width Gain EQ1 100Hz 1.4Q 0.0dBNavigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dBPresets Preset RecallPreset Store Preset Name Store My SystemStereo / Mono Formats Input DSP block diagramOutput DSP block diagram DSP Processing LayoutInput Channels DSP ProcessingA Freq Shape HPF 20.0Hz LR24 High and Low shelving filters Parametric EqualisationParametric filters Output Channels DelayGain and Polarity High and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing LimitersUtility functions UtilitiesAudio Input Connectors Racking, Cables and Connections AMP-890 Aspect System Amplification RackInput Connections OptionsOutput Connections Amplifier Rack Signal WiringMid-High Outputs Break-out Cables NL4 bass Extension Cables Break-out cables NL8 mid-highMains Connections General Features & Facilities T-45 High Efficiency Audio Power AmplifiersFront Panel Functions T-25 Front Panel Functions T-45 Mechanical Installation Audio Connections & Controls Voltage RangePolarity Gain and Sensitivity SettingsInput Impedance Damping Factor Attenuation & Gain SettingCooling System Long Speaker LinesMaintenance To rotate the horn moulding from ‘A’ mode to ‘B’ mode Removal of the high frequency driver To rotate the horn moulding from ‘B’ mode to ‘A’ modeRemoval of the high-mid frequency driver Removal of the low-mid frequency drive units General MaintenancePaintwork TA-890 Technical Specifications Serial Numbers WarrantyTA-890