TOA Electronics SR-A12SWP, SR-RF12 Safety Precautions, Safety Symbol and Message Conventions

Page 3

1. SAFETY PRECAUTIONS

Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation.

Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.

After reading, keep this manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which could result from mishandling. Before operating your product, read this manual first and understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

WARNING

CAUTION

Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

WARNING

Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface. Doing so may result in the unit falling down and causing personal injury and/or property damage.

Refer all installation work to the dealer from whom the speaker was purchased. Installation for flying requires extensive technical knowledge and experience. The speaker may fall off if incorrectly installed, resulting in possible personal injury.

Flying Precautions

Be sure to follow the instructions below. Otherwise, the suspension wires or belts may be off or snap and the speaker may fall off, causing personal injury.

·Check to confirm that the suspension wires and belts are strong enough to withstand the speaker load.

·The connectors of the suspension wires and belts must be securely linked with those of the speaker.

·All parts and components (such as enclosures, metal pieces, and screws) must be free from any deformation, crack, and corrosion.

·Be sure to use screws supplied with the optional flying hardware when installing the speaker using such hardware.

Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket. Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.

(SR-A12LWP, SR-A12SWP, SR-RF12WP only) When installing the unit in a snowy area, take appropriate measures to prevent snow from lying on the unit. If the snow lies on the unit, the unit may fall, causing personal injuries.

Owing to the unit's size and weight, be sure that at least two persons are available to install the unit. Failure to do so could result in personal injury.

Do not use other methods than specified to mount the bracket. Extreme force is applied to the unit and the unit could fall off, possibly resulting in personal injuries.

Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so may cause the speaker to fall, resulting in material damage and possible personal injury.

Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent accidents that could result in personal injury.

Use only the specified mounting brackets. Doing otherwise may cause the unit or component to fall off, resulting in personal injury.

Do not mount the unit in locations exposed to constant vibration. The mounting bracket can be damaged by excessive vibration, potentially causing the unit to fall, which could result in personal injury.

3

Image 3
Contents Operating Instructions Tilt Joint PlateStacking Table of ContentsSafety Symbol and Message Conventions Safety PrecautionsPage SR-A12L FeaturesDimensions General DescriptionSR-A18B SR-A12SSR-A12LWP SR-A12SWPUnit mm SR-TP12 SR-RF12, SR-RF12WPSR-A12LWP and SR-A12SWP for outdoor use Input ConnectorsSR-A12L, SR-A12S and SR-A18B for Indoor use SR-A12L, SR-A12SSR-A12LWP, SR-A12SWP Internal Wiring DiagramSystem using the SR-A12L, SR-A12S, SR-A12LWP or SR-A12SWP ConnectionsDigital Processor Settings Flying General DescriptionSR-A12LWP SR-A12SWP SR-RF12WP Rigging Frame assembly Joining the Enclosure to the Rigging Frame High box assembly diagram Subwoofer assembly diagramHigh box finished assembly diagram Subwoofer finished assembly diagramJoining Enclosures Page Page When attaching the Mounting Plates forward positions SR-RF12 Rigging Frame assemblyAssembly diagram When attaching the Mounting Plates to the center positionsMounting the Enclosure to the Rigging Frame Subwooter finished assembly diagramForbidden stacking example Typical stacking exampleSR-TP12 Tilt Joint Plate Tilting the Enclosure DownwardJoined view with sub-woofer Joined view with rigging frameSR-A12S x1, SR-A12L SR-A18B x1, SR-A12S x1, SR-A12LSR-A12LWP SR-A12SWP SpecificationsSR-A18B