Lincoln Electric SP-100 service manual Input Connections, Gas Solenoid Inlet Fitting, Power

Page 12

A-5	INSTALLATION

Return to Section TOC

Return to Section TOC

WARNING

BUILDUP OF SHIELDING GAS may harm health or kill.

• Shut off shielding gas supply when not in use.

•SEE AMERICAN NATIONAL STANDARD Z-49.1, “SAFETY IN WELDING AND CUTTING” PUB- LISHED BY THE AMERICAN WELDING SOCIETY.

1.Chain the cylinder to a wall or other stationary sup- port to prevent the cylinder from falling over. Insulate the cylinder from the work circuit and earth ground.

FIGURE A.5

Flow Regulator

Cylinder Valve

3.Attach the flow regulator to the cylinder valve and tighten the union nut securely with a wrench. The flow regulator for carbon dioxide must have a plas- tic washer seated in the fitting that attaches to the cylinder to prevent leakage.

4.Refer to Figure A.6. Attach one end of inlet gas hose to the outlet fitting of the flow regulator and tighten the union nut securely with a wrench. Connect the other end to the SP-100 Gas Solenoid Inlet Fitting (5/8-18 female threads — for CGA — 032 fitting). Make certain the gas hose is not kinked or twisted.

INPUT CONNECTIONS

Refer to Figure A.6.

The SP-100 has two input connections, the power input cable, and the Gas Solenoid Inlet Fitting. Both connections are located on the rear of the machine.

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

FIGURE A.6

Gas Hose

Gas Solenoid

Inlet Fitting

2. With the cylinder securely installed, remove the	Power
cylinder cap. Stand to one side away from the out-	Input
let and open the cylinder valve very slightly for an	Cable
instant. This blows away any dust or dirt which may
have accumulated in the valve outlet.

WARNING

BE SURE TO KEEP YOUR FACE AWAY FROM THE VALVE OUTLET WHEN “CRACKING” THE VALVE. Never stand directly in front of or behind the flow regulator when opening the cylinder valve. Always stand to one side.

SP-100

Image 12

Contents SP-100 Safety Electric Shock can killARC Rays can burn Fumes and Gases can be dangerousCylinder may explode if damaged Welding Sparks can cause fire or explosionElectric and Magnetic Fields May be dangerousPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation SectionInstallation Technical Specifications SP-100Safety Precautions Read entire installation section before startingInstallation Identify and Locate ComponentsWork Clamp Installation Select Suitable LocationOutput Connections TiltingGUN Installation Connecting GUN Cable to the SP-100GAS Connection Power Input ConnectionsGas Solenoid Inlet Fitting InputCode Requirements for Input Connections Requirements for Maximum OutputRequirements for CSA Rated Output Requirements for Rated OutputSP-100 Table of Contents Operation Wear eye, ear and body protec- tionOperational Features and Controls Design Features AdvantagesGeneral Description OffWire Loading Welding OperationsProcess Guidelines Sequence of OperationFriction Brake Adjustments Refer to Figure B-4Shielding GAS Making a WeldOverload Protection SP-100 Accessories Section 1ACCESSORIES Replacement PartsLincoln GAS Regulator Kits K467 Input Line Cord Innershield Welding KitsMaintenance Section Maintenance Items Requiring no MaintenanceRoutine and Periodic Maintenance Changing the Contact TIP Changing Drive RollLiner trim length for the Magnum 100L gun red trigger Figure D.3 SP-100 SUB Assemblies SP-100 Theory of Operation Figure E.1 Input Power Circuits Input Line VOLTAGE, FAN Motor and Main TransformerOutput CONTROL, RECTIFICA- Tion and Voltage Feedback Figure E.2 Output CircuitsTRIGGER, GAS Solenoid and Wire Drive 3THEORY of OperationSCR Operation Figure E.4 SCR OperationThermostat protects the machine from Troubleshooting Section Oscilloscope Waveforms1TROUBLESHOOTING & Repair HOW to USE Troubleshooting GuideTroubleshooting & Repair PC Board Troubleshooting ProceduresTroubleshooting Guide Authorized Field ServiceFacility Below Code 9794 only Problems Symptoms Possible Areas of MisadjustmentsRecommended Course of Action Code 9794 and AboveFeeding Problems Troubleshooting Guide PC Board Connector Locations Codes 9794 and above 6J1 10J2 1J1 1J2 Codes below SP-1009TROUBLESHOOTING & Repair Scope SettingsVolts Volts/Div Normal Open Circuit Voltage WaveformVolts Typical Output Voltage Waveform Machine LoadedAbnormal Open Circuit Voltage Waveform Procedure Description ProcedureFAN Blade and Motor Removal Tools RequiredWire Drive Assembly Removal Motor Removal Procedure1A. for Codes Above 1B. for Codes belowWire Speed Range Retest After RepairMain Transformer Secondary Voltages Test Points Input Amps AT Rated Output Input Amps AC @ Output DCSP-100 Electrical Diagrams Section Wiring Diagrams WiringDiagram SP-100 Wiring Diagram Codes Below 4 5 1 MElectrical Diagrams Electrical Diagrams Control P.C. Board G1842Control P.C. Board G2314 Control P.C. Board G2314 SCR1, SCR2 SCR 81 Heatsink AsblyMachine Schematic Codes 9794 and Above ErrorMachine Schematic Codes Below 86R R63R64 1 5 KSVM Error Reporting Form