Lincoln Electric IM359-G manual Safety, California Proposition 65 Warnings

Page 2

i

SAFETY

i

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents are known to the State of California to cause can- cer, birth defects, and other reproductive harm.

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The Above For Diesel Engines

The Above For Gasoline Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame welding arc or when the engine is running. Stop the engine and allow it to cool before refueling to prevent spilled fuel from vaporizing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes have been

eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle control rods while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.

1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.

ELECTRIC AND MAGNETIC FIELDS may be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, and welders having a pacemaker should consult their physician before welding.

2.c. Exposure to EMF fields in welding may have other health effects which are now not known.

2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work cables. If the electrode cable is on your right

side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

Page 1 Page 3
Image 2
Page 1 Page 3
Contents LN-25 Portable CV/CC Semiautomatic Wire Feeder Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Sûreté Pour Soudage a L’ArcPlease Examine Carton and Equipment For Damage Immediately Table of Contents Installation Power Source Connection INSTALLATIONA-2Safety Precautions MAR97GUN Cable Connection to Feeder 3INSTALLATIONINVERTEC, CV300 and Other Newer Lincoln Power Sources CV AdapterWeld Cable Connection INSTALLATIONA-4Wire Feed Drive Roll and Guide Tube Kits Electrode Cable ConnectionRecommended Processes and Equipment 1OPERATIONGeneral Description Welding CapabilityOPERATIONB-2 LN-25 Instruments and Controls3OPERATION Loading Electrode OPERATIONB-4Sequence of Operation Mounting 22 to 30 LB READI-REELCOILS5OPERATION Loading Wire DriveIdle Roll Pressure Setting Setting ARC Sensing Wire Feed Speed VV CC Mode Presetting Wire Feed SpeedSetting Constant Wire Feed Speed CV Mode OPERATIONB-67OPERATION Making a WeldWelding Procedure AT END of CoilOPERATIONB-8 Overvoltage Shutdown 9OPERATIONAutomatic Protection Shutdown Motor Overload ShutdownACCESSORIESC-1 LN-25 Option ChartK430-1 GAS Solenoid KIT 2ACCESSORIES Optional AccessoriesK434-1 GAS Flow Timer KIT ACCESSORIESC-3 Remote Output Control Options and Control Cable Assemblies4ACCESSORIES K577-1 Rear Handle KIT ACCESSORIESC-5Control KIT 6ACCESSORIES Figure C.1Adjusting Speed Sensor Module MAINTENANCED-1Routine Maintenance Circuit Protection and Automatic Shutdown2MAINTENANCE Calibration of LN-25 Wire Speed DialTROUBLESHOOTINGE-1 HOW to USE Troubleshooting GuideRecommended Course of Action 2TROUBLESHOOTINGProblems Possible Areas Symptoms Misadjustments Troubleshooting 4TROUBLESHOOTING Output ProblemsDiagram 2DIMENSIONS LN-25 Physical Dimensions

IM359-G specifications

The Lincoln Electric IM359-G is a state-of-the-art multi-process welder designed to offer exceptional versatility and performance in various welding applications. This machine is particularly well-suited for professional welders, fabricators, and hobbyists alike who demand precision and reliability in their welding tasks.

One of the standout features of the IM359-G is its capability to handle multiple welding processes, including MIG, TIG, and Stick welding. This multi-process functionality allows users to switch seamlessly between different welding techniques, making it ideal for complex projects requiring various welding methods. The machine is equipped with advanced inverter technology, which contributes to a smaller, lighter design while enhancing energy efficiency. This technology ensures that users can experience consistent output regardless of the welding conditions, providing high-quality results every time.

Another important characteristic of the IM359-G is its user-friendly interface. The intuitive control panel is designed for easy operation, featuring clear digital displays and simple adjustments. This allows both novice and experienced welders to quickly adapt to the machine and optimize their settings for specific tasks. Additionally, the Lincoln Electric IM359-G comes with a built-in memory function that can store frequently used settings, streamlining workflow and increasing productivity.

The IM359-G is also compatible with Lincoln Electric’s Smart Voltage Sensing technology, which automatically detects the input voltage and adjusts settings accordingly. This feature ensures optimal performance, whether the welder is in a shop setting or on-site with varying power supplies. Coupled with excellent arc stability, this technology helps minimize spatter and provides precise control over the welding process.

Durability is another hallmark of the Lincoln Electric IM359-G. Built with robust materials and designed for longevity, the machine is capable of withstanding the rigors of demanding work environments. Furthermore, it is equipped with advanced thermal overload protection, ensuring that the welder operates within safe limits, preventing damage to the unit.

In conclusion, the Lincoln Electric IM359-G is an impressive multi-process welder that combines advanced technology, user-friendly controls, and robust construction. Its versatility in handling multiple welding processes makes it suitable for a wide range of applications, while features like Smart Voltage Sensing and thermal overload protection ensure reliable performance. Whether for professional use or serious hobbyists, the IM359-G stands out as a top choice for those looking to enhance their welding capabilities.
Top Page Image Contents