Lincoln Electric IM581 manual Safety, California Proposition 65 Warnings

Page 2

i

SAFETY

i

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents are known to the State of California to cause can- cer, birth defects, and other reproductive harm.

The Above For Diesel Engines

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you pur- chase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame weld- ing arc or when the engine is running. Stop the engine and allow it to cool before refuel- ing to prevent spilled fuel from vaporizing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes

have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in posi- tion and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle control rods while

the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.

1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.

ELECTRIC AND MAGNETIC FIELDS may be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, and welders having a pacemaker should consult their physician before welding.

2.c. Exposure to EMF fields in welding may have other health effects which are now not known.

2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work cables. If the electrode cable is on your right side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

Page 1 Page 3
Image 2
Page 1 Page 3
Contents IM581 Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Safety Safety Préca Utions DE Sûreté SAE400 WELD’N AIRThank You Table of Contents Height Width Depth Weight InstallationTechnical Specifications SAE400 WELD’N AIR Stacking Safety PrecautionsLOCATION/VENTILATION Angle of OperationPRE-OPERATION Engine and Compressor Service Spark Arrester Battery ConnectionEngine Cooling System Table A.1 Combined Length of Electrode and Work Cables Welding Output CablesMachine Grounding Operating Instructions Safety InstructionsOperation General DescriptionDesign Features and Advantages Duty CycleEngine Controls Welder Controls AIR Compressor Controls Starting Instructions Engine OperationTypical Fuel Consumption BREAK-IN PeriodAccessories Periodic Maintenance MaintenanceRoutine Maintenance Engine Compressor Maintenance Components Make Part Number Bearing MaintenanceCommutator and Brush Maintenance Cooling System1TROUBLESHOOTINGE-1 HOW to USE Troubleshooting GuideTroubleshooting Symptoms Course of ActionRecommended Troubleshooting Problems Possible Cause Recommended AIR WiringSAE400 WELD’N Engine Wiring Diagram SAE-400 WELD’N AIR Dimension PrintBasic Course $700.00Precaucion Aviso DE

IM581 specifications

The Lincoln Electric IM581 is an innovative solution designed for advanced welding applications. This multi-process welder stands out with its versatility, allowing users to perform MIG, TIG, and stick welding seamlessly. Such adaptability makes it ideal for a wide range of industries, from automotive to construction.

One of the hallmark features of the IM581 is its intuitive digital interface. The display is user-friendly, allowing operators to easily select welding parameters and monitor real-time performance metrics. This digital technology not only enhances ease of use but also improves precision during welding, reducing the likelihood of errors.

Another significant characteristic of the IM581 is its robust power range. The machine is equipped to handle a wide spectrum of materials and thicknesses, making it suitable for both thin-gauge and heavy-duty applications. The power output is adjustable, enabling users to optimize their welding for different types of metal such as steel, aluminum, and stainless steel.

The IM581 is also designed with mobility in mind. It features a compact and lightweight construction, ensuring it can be easily transported between job sites. Despite its portable design, the machine does not compromise on performance; it delivers stable arcs, ensuring clean and consistent welds with minimal spatter.

In terms of safety, the Lincoln Electric IM581 incorporates several protective features. It includes thermal overload protection, safeguarding the machine from excessive heat during extended use. Additionally, it has built-in safety mechanisms to prevent voltage spikes, enhancing longevity and reliability.

Moreover, the IM581 is compatible with advanced welding technologies, such as Lincoln Electric's proprietary "Infinite Voltage Control" which allows users to finely adjust the output voltage for optimal arc stability. This feature is particularly beneficial for applications requiring precise control and quality.

Overall, the Lincoln Electric IM581 is an exceptional welding machine that combines versatility, user-friendly operation, and superior performance. Whether it's critical high-strength applications or routine repairs, this welder is engineered to meet and exceed the expectations of professionals in various industries. Its advanced technologies and dependable characteristics make it a valuable addition to any welding toolkit.
Top Page Image Contents