Final Inspection & Start-up Checklist

Inspect and ensure that all components and accessories have been installed properly and that they have not been damaged during the installation progress.

Check the condensate water drain(s) to ensure that they are adequate for the removal of condensate water, and that they meet the approval of the end user.

Ensure that all installation instructions concerning clearances around the unit have been adhered to. Check to ensure that the unit air ﬁlter, indoor coil, and outdoor coil are free from any obstructions.

Ensure that the circuit breaker(s) or fuse(s) and supply circuit wire size have been sized correctly. If the unit was supplied with a power supply cord, insure that it is stored properly.

Ensure that the entire installation is in compliance with all applicable national and local codes and ordinances having jurisdiction.

Secure components and accessories, such as a decorative front cover.

Start the unit and check for proper operation of all components in each mode of operation.

Instruct the owner or operator of the units operation, and the manufacturer's Routine Maintenance.

NOTE: A log for recording the dates of maintenance and/or service is recommended.

Present the owner or operator of the equipment with the Installation & Operation Manual, all accessory installation instructions, and the name, address and telephone number of the Authorized Friedrich Warranty Service Company in the area for future reference if necessary.

This is a warm weather appliance

Your air conditioner is designed to cool in warm weather when the outside temperature is above 60°F (15.6°C) and below 115°F (46.1°C), so it won't cool a room if it is already cool outside.

Condensation is normal

Air conditioners actually pump the heat and humidity from your room to the outside. Humidity becomes water, and your air conditioner will use most of the water to keep the outside coil cool. If there is excessive humidity, there may be excess water that will drip outside. This is normal operation.

Frosting

This usually occurs because of insufﬁcient airﬂow across the coils, a dirty ﬁlter, cool damp weather, or all of these. Set the SYSTEM mode to FAN ONLY and the frost will disappear. Setting the thermostat a little warmer will probably prevent the frosting from recurring.

Noises

All air conditioners make some noise. Friedrich units are designed to operate as quietly as possible. An air conditioner mounted in a wall is quieter than one mounted in a window. It is important to ensure that the chassis seal gasket (Item 14) is properly installed (refer to installation instructions).

SQ08, SQ05, SQ06, SQ10 specifications

Friedrich is a renowned name in the HVAC industry, known for its innovative solutions in cooling and heating technologies. Among its impressive lineup, the SQ series, consisting of models SQ10, SQ06, SQ05, and SQ08, stands out for their robust features and advanced performance.

One of the defining characteristics of the SQ series is its energy efficiency. Each model is designed to optimize energy use, allowing for significant cost savings while reducing the environmental impact. This is primarily achieved through the incorporation of advanced inverter technology, which adjusts the compressor speed according to cooling or heating demand, maintaining a comfortable indoor climate without excessive energy consumption.

The SQ series units are equipped with high-performing compressors that provide rapid cooling and heating capabilities. This means that users can expect fast temperature adjustments, ensuring a comfortable environment even during extreme weather conditions. Moreover, the noise levels of these units have been engineered to remain low, offering whisper-quiet operation that does not disrupt daily activities.

Control and convenience are also paramount in the SQ series. The units feature smart technologies that allow for remote operation through mobile applications. This means homeowners can adjust temperatures, set schedules, and monitor their energy usage from anywhere, adding a layer of convenience to the user experience. The user-friendly interface and intuitive controls further enhance accessibility.

Durability and reliability are core elements of the SQ models. Constructed with high-quality materials and components, these units are built to withstand the rigors of daily use. The units also come with comprehensive warranties, offering peace of mind to users regarding long-term performance.

In summary, Friedrich's SQ10, SQ06, SQ05, and SQ08 units showcase a blend of energy efficiency, advanced technology, and user-centric features. With their quiet operation, fast temperature adjustments, and smart connectivity, they provide an ideal solution for reliable heating and cooling needs in residential or commercial spaces. The robust design ensures longevity, making Friedrich a trusted choice in climate control solutions.