Lincoln Electric 500 manual High Frequency Generators for TIG Applications, Remote Control

Page 13

A-5

INSTALLATION

A-5

 

 

 

MUFFLER OUTLET PIPE

Remove the plastic plug covering the muffler outlet tube. Using the clamp provided secure the outlet pipe to the outlet tube with the pipe positioned such that it will direct the exhaust in the desired direction.

SPARK ARRESTER

Some federal, state or local laws may require that gasoline or diesel engines be equipped with exhaust spark arresters when they are operated in certain loca- tions where unarrested sparks may present a fire haz- ard. The standard muffler included with this welder does not qualify as a spark arrester. When required by local regulations, a suitable spark arrester, must be installed and properly maintained.

CAUTION

An incorrect arrester may lead to damage to the engine or adversely affect performance.

------------------------------------------------------------------------

HIGH FREQUENCY GENERATORS FOR TIG APPLICATIONS

The K799 Hi-Freq Unit and the K930-1 or -2 TIG Module are suitable for use with the Commander 500. The Commander 500 is equipped with the required R.F. bypass circuitry for the connection of high fre- quency generating equipment. The high frequency bypass network supplied with the K799 Hi-Freq Unit does NOT need to be installed into the Commander 500.

The Commander 500 and any high frequency generat- ing equipment must be properly grounded. See the K799 Hi-Freq Unit and the K930-1 or-2 TIG Module operating manuals for complete instructions on instal- lation, operation, and maintenance.

REMOTE CONTROL

OUTPUT

The Commander 500 is equipped with a 6-pin & 14-pin connector. The 6-pin connector is for connecting the K857 or K857-1 Remote Control (Optional) or in the case of TIG welding applications, with the foot or hand Amptrol (K870 or K963-1 respectively).

The 14-pin connector is used to directly connect a wire feeder or TIG Module (K930-1 or -2) control cable.

NOTE: When using the 14-pin connector, if the wire feeder has a built in power source output control, do not connect anything to the 6-pin connector.

WELDING TERMINALS

The Commander is equipped with a toggle switch for selecting "hot" welding terminals when in the "WELD TERMINALS ON" position or "cold" welding terminals when in the "REMOTELY CONTROLLED" position.

COMMANDER 500

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Safety Depends on You CommanderCalifornia Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents Section D Section CSection E Section FWelding Range Open Circuit Voltage Auxiliary Power1 InstallationHEIGHT2 Width Depth Weight Bore x StrokeLocation / Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingEngine Cooling System Battery Connection PRE-OPERATION Engine ServiceOIL Fuel USE Diesel Fuel onlyHigh Frequency Generators for TIG Applications Remote ControlWelding Terminals Standby Power Connections Auxiliary Power ReceptaclesWelding Output Cables Machine GroundingPower Connection of the LN-25 to the Commander Connection of Lincoln Electric Wire FeedersConnection of LN-7 or LN-8 to the Commander Remotely Controlled Connection of AN LN-23P Wire Feeder to the CommanderDesign Features and Advantages Safety InstructionsOperation General DescriptionOther Features For Auxiliary PowerK1639-1 Commander 500 Standard Model Welding CapabilityRUN Stop Switch Controls and SettingsStart Pushbutton Fuel Level Gauge and LightEngine Alternator Ammeter K1639 Idler SwitchHour Meter Auxiliary Power Controls Starting the Engine Engine OperationStopping the Engine BREAK-IN Period Welder OperationTypical Fuel Consumption Stick WeldingTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Commander 500 Settings When Using the K799 HI-FREQ UnitAuxiliary Power Operation Table B.4 Commander 500 Simultaneous Welding and Power Loads Optional Field Installed Accessories AccessoriesK899-1 Spark Arrestor KIT Easily mounts to standard muffler Recommended Optional Equipment Wire Feed Welding OptionsStick TIGRoutine and Periodic Maintenance MaintenanceEngine Maintenance Fuel PRE-FILTER/WATER Separator ASSEM- BLY Fuel FiltersWater Separator Element Cooling System Cooling Blower Belt Battery HandlingWelder / Generator Maintenance Nameplates / Warning Decals MaintenanceCleaning Brush Removal and ReplacementHOW to USE Troubleshooting Guide TroubleshootingPossible Areas SymptomsCourse of Action Function Problems Output Problems Commander 500 Wiring Diagram for 10838 and below Connection Diagram DiagramsConnection Diagram Diagrams Diagrams Commander / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagram Engine Welders /LN-8 Connection DiagramConnection Electric Shock can killConnection Diagram Diagrams Diagrams M18962 Commander $700.00 Basic CoursePrecaucion Aviso DE
Related manuals
Manual 54 pages 2.58 Kb Manual 54 pages 42.7 Kb

500 specifications

The Lincoln Electric 500 is a hallmark of innovation in arc welding technology, designed to cater to the rigorous demands of both industrial applications and serious hobbyist projects. This powerful machine is known for its reliability, versatility, and user-friendly design, making it an essential tool for professional welders and those looking to tackle various welding tasks with ease.

One of the standout features of the Lincoln Electric 500 is its robust power output. With a capability of up to 500 amps, it can handle a wide range of welding processes, including Stick, TIG, and MIG welding. This flexibility allows welders to use the machine for different types of metals, including steel, stainless steel, and aluminum, making it suitable for diverse applications from automotive to construction industries.

The machine's digital interface enhances user experience by providing precise control over the welding parameters. The intuitive display allows for easy adjustments of voltage and wire speed, ensuring optimal welding conditions are achieved. This feature is especially beneficial for beginners who may require additional support as they learn the intricacies of welding.

The Lincoln Electric 500 is also equipped with advanced technologies that enhance efficiency and welding quality. One such technology is the inverter system, which optimizes the power source for superior arc stability and improved penetration. This results in cleaner welds with minimal spatter, reducing the need for post-welding cleanup. Furthermore, the machine’s duty cycle is impressive, meaning it can operate for extended periods without overheating, a critical factor in high-production environments.

Another significant characteristic of the Lincoln Electric 500 is its portability. Weighing in at a manageable level and designed with built-in carrying handles, it’s easy to transport between job sites. This feature is particularly valuable for mobile welders who need to work in various locations.

Safety is paramount in welding operations, and the Lincoln Electric 500 integrates various safety features designed to protect the user. Overload protection and thermal overload indicators help prevent damage to the machine and injury to the operator, ensuring a reliable and safe working environment.

Overall, the Lincoln Electric 500 stands out not only for its performance but also for its thoughtful engineering that prioritizes user safety, comfort, and versatility. It is a dependable choice for anyone looking to produce high-quality welds while enjoying the benefits of advanced welding technology.
Top Page Image Contents