Craftsman 919.722020 owner manual How to Stop, Before First Start-up

Page 14

Female Tire Chuck: Attaches to the hose end to be used to inflate tires. Note: To ensure correct tire pressure use a tire pressure gauge.

Hose Adapter: Attaches to hose end to allow the use of accessories. Blow Gun Adapter: Attaches to hose end or blow gun (sold separately, not shown) to allow the inflating needle to be used.

Inflating needle: Attaches to blow gun adapter to be used to inflate sport balls.

Tapered Inflator: Attaches to hose adapter or blow gun (sold separately) to be used to inflate toy inflatables/air mattresses.

Extension Tube: Attaches to hose adapter or blow gun (sold separately) to be used for air blowing, drying, and for specialized inflating.

Drain Valve (not shown): The drain valve is located at the base of the air tank and is used to drain condensation at the end of each use. Cooling System (not shown): This compressor contains an advanced design cooling system. At the heart of this cooling system is an engineered fan. It is perfectly normal for this fan to blow air through the vent holes in large amounts. You know that the cooling system is working when air is being expelled.

Air Compressor Pump (not shown): Compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet.

Check Valve (not shown): When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air compressor reaches "cut-out" pressure, the check valve "closes", allowing air pressure to remain inside the air tank.

How to Use Your Unit

How to Stop:

1.Set the Off/Auto switch to "OFF".

Before First Start-up

Break-in Procedure

Risk of Unsafe Operation. Serious

damage may result if the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service.

1.Make sure the Off/Auto switch is in the "OFF" position.

2.Turn the regulator knob counterclockwise until it stops.

3.Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage and Circuit Protection paragraph in the Installation section of this manual.)

4.Open the drain valve fully (counterclockwise) to permit air to escape and prevent air pressure build up in the air tank during the break-in period.

5.Move the Off/Auto switch to "AUTO" position. The compressor will start.

6.Run the compressor for 15 minutes. Make sure the drain valve is open and there is minimal air pressure build-up in tank.

7.After 15 minutes, close the drain valve (clockwise). The air receiver will fill to "cut-out" pressure and the motor will stop.

The compressor is now ready for use.

D29495

14- ENG

Page 13 Page 15
Image 14
Page 13 Page 15
Contents AIR Compressor Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B8Table of Contents Important Safety Instructions Specification ChartSafety Guidelines Definitions Model NoHazard Attachments & Accessories Hazard Hazard Hazard Glossary AccessoriesAccessories Tools Assembly Risk of Electrical Shock. Improper InstallationLocation of the Air Compressor Plug Grounded Outlets Grounding PinExtension Cords Voltage and Circuit ProtectionDescription of Operation OperationKnow Your Air Compressor Inflating Tapered Not shown Needle InflatorHow to Stop Before First Start-upHow to Start Before Each Start-UpRisk of Bursting. If the safety valve MaintenanceTo Check Safety Valve Customer ResponsibilitiesStorage Smaller CompartmentTroubleshooting OvertightenCheck for low voltage 30-31 Table DES Matières22-27 32-34Consignes DE Sécurité Importantes Tableau DES SpécificationsMesures DE Sécurité Définitions 919.722020Conserver ces directives Avertissement Risque dexplosion ou dincendie PréventionAvertissement Risque de projection dobjets Avertissement Risque déclatementRisque Avertissement Risque de choc électrique Avertissement Risque par inhalationAvertissement Risque de chute Avertissement Risque de brûluresAvertissement Risque relié aux pièces mobiles Avertissement Risque dune utilisation dangereuse Lexique AccessoiresAccessoires OutilsAssemblage Assemblage du boyauRisque de choc électrique ! UNE Mise À Emplacement du compresseur dairRisque de choc électrique ! En cas de Risque dune utilisation RallongesProtection contre la surtension et Protection du circuit Description du fonctionnement UtilisationFamiliarisez-vous avec votre compresseur dair Avant le premier démarrage Utilisation de lappareilArrêt de lappareil Procédures de rodage Risque dune utilisationAvant chaque mise en marche Mise en marcheVérification de la soupape de sûreté EntretienResponsabilités du client Vidange du réservoirRangement Compartiment plus petitDépannage SerrerDiminuez la quantité dair utilisé Get it fixed, at your home or ours
Top Page Image Contents