Friedrich 920-087-09 (12/10) operation manual Chassis Install Preparation, Suffocation Hazards

Page 16

Chassis Install Preparation

Check to be sure the wall sleeve, extension (if used), grille, and drain kit are installed properly before chassis installation.

1. Remove the weatherboard and center support from the sleeve (if

NOTE:

To avoid breaking the door or hinge pins, do not apply excessive

still in place). Be sure an outdoor grille is attached.

 

force when installing.

Figure 18

WALL SLEEVE

WEATHERBOARD

CENTER SUPPORT

FRP015

Figure 19

PIN

CONTROL

DOOR

INSERT PIN

IN THIS LOCATION

FRP016

NOTE: Use a wall sleeve adapter kit (PXSE) if installing a P-Series chassis in a T-Series sleeve.

WARNING

Suffocation Hazards

Keep bag away from babies and children.

Do NOT use in cribs, beds or playpens. Destroy immediately after opening. This bag is NOT a toy.

Failure to do so can result in personal injury and/or death.

IMPORTANT: When installing a Friedrich PTAC into an existing sleeve, it is important to ensure that the unit is installed completely. Inspection of the air seal between the condenser air baffles and around the indoor mounting flange is recommended.

In some cases additional gaskets or baffling may be required.

2.Remove the front cover contained in a protective plastic bag from chassis. Remove the bag and dispose of it properly..

.

If the control door is not installed, follow these steps:

a.From the front cover, slide the right control door pin into the hole on the right side of the front cover.

b.Slide the left door pin into the hole on the left side of the front cover opening.

c.Snap cover into place.

16

Image 16
Contents Ptac Table of Contents Congratulations Read Installation Operation ManualGeneral Instructions General Specifications Installation ChecklistPtac Installation Recommendations Typical Building Plan ViewWall Sleeve Installation Instructions Pdxws For Deep Wall Installation Greater than 13 1/4 SeeTypical Wall Sleeve Installation Falling Object HazardAlternate Wall Installations Panel WallFrame and Brick Veneer Curtain WallDimensions Wall Sleeve AttachmentOne-Piece Deep Wall Sleeve Installation Pdxwsext Lintel InstallationDrain Kit Location and Installation Internal DrainDrain Tube Installation See Figure Cover Plate InstallationDrain Kit Installation Pxga Standard Grille Installation Instructions Standard GrilleAll 230/208 volt units are equipped with power cords Power Cord Information 230/208V models onlyElectrical Rating Tables Power Cord Installation Electrical Wiring for 265 Volt ModelsElectrical Shock Hazard To Chassis Junction Chassis Install Preparation Suffocation HazardsShipping Tape Location Unit Damage HazardShipping Screw Location Excessive Weight Hazard Chassis InstallationSecuring Unit How To Connect Power ConnectionFriedrich Ptac Digital Control and Unit Features Page System Configuration Dip Switch Setting Digital Control User Input ConfigurationDip Switches Digital Control Operation Remote Control Thermostat Installation Desk Control Terminals Energy ManagementRoutine Maintenance Basic Troubleshooting Complaint Cause SolutionService & Assistance Accessories New Construction AccessoriesPxcja Friedrich Packaged Terminal AIR Conditioners and Heat Pumps This page Intentionally Left Blank This page Intentionally Left Blank This page Intentionally Left Blank

920-087-09 (12/10) specifications

The Friedrich 920-087-09 (12/10) is a remarkable air conditioning unit that exemplifies innovation in climate control technology. Designed for both residential and commercial environments, this model stands out for its efficiency, reliability, and user-friendly features.

One of the key characteristics of the Friedrich 920-087-09 is its impressive cooling capacity. With a nominal cooling power of 12,000 BTU, it is ideal for medium to large spaces, effortlessly maintaining comfortable indoor temperatures even during the hottest months. The unit offers a seasonal energy efficiency ratio (SEER) that meets contemporary standards, ensuring that it operates efficiently while consuming less energy. This feature not only lowers electricity bills but also reduces the overall environmental impact.

The Friedrich 920-087-09 is equipped with advanced inverter technology, allowing it to adjust its cooling power according to the temperature needs of the room. This results in quieter operation and enhanced energy savings as the unit avoids the frequent on-off cycles typical of conventional systems. Furthermore, the unit boasts a variable-speed compressor that guarantees consistent performance and improved humidity control.

Another standout feature of the Friedrich 920-087-09 is its sophisticated air filtration system. It includes a washable filter that captures dust, pollen, and other airborne particles, promoting cleaner air quality. This is particularly beneficial for those with allergies or respiratory issues, creating a healthier living environment.

The unit also features a customizable digital thermostat that allows users to set precise temperature preferences. With its user-friendly interface, users can easily switch between different modes, including cooling, heating, and dehumidifying, adding to the flexibility of the system. Additionally, Friedrich's exclusive Quiet Master technology minimizes noise levels, making it suitable for bedrooms, offices, and other quiet areas.

The Friedrich 920-087-09 also comes with a range of connectivity options, including Wi-Fi integration. This functionality allows users to control the air conditioning unit remotely through a smartphone app, making it exceptionally convenient for those with busy lifestyles.

Overall, the Friedrich 920-087-09 (12/10) combines cutting-edge technology, energy efficiency, and a host of user-friendly features, making it a top choice for anyone looking to enhance their indoor comfort. Its design is not only functional but also aesthetically pleasing, allowing it to blend seamlessly with a variety of interiors.