APC 412 kVA, SYBT3 installation manual Installation

Page 27

CHAPTER 4: INSTALLATION

3.Remove the input-wiring access panels ￿.

4.Remove the input and output (if applicable) knockouts ￿.

5.Ensure that the battery jumper is installed between the terminal blocks ￿. The battery jumper is used to disconnect batteries during shipment, if the battery modules are shipped installed.

6.Attach input ￿ and if applicable, output ￿ conduit and feed the wire through the holes on the wiring panel.

7.Connect the wires to the terminal block ￿.

8.Inspect the connections.

9.With the input circuit breaker still OFF,

turn ON the branch circuit (mains) and measure the L1-L2/N voltage.

•If the value does not match your branch voltage (200/208/220/230 or 240), check your wiring.

•Turn OFF the branch circuit (mains) and complete the installation.

10.Replace the access panels and fasten with the screws.

11.After the UPS is connected to the branch circuit (mains), install the three (3) “Isolate UPS before working on this circuit” labels on the branch circuit (mains) disconnect panels.

23

Page 26 Page 28
Image 27
Page 26 Page 28
Contents APC Symmetra RM KVA UPS Installation Manual Page Safety and General Information Installation General Equipment Safety Handling SafetyConventions Used in this Manual Deenergizing Safety Electrical SafetyBattery Safety North America and 208 V Countries Europe and 230 V CountriesJapan and 200 V Countries Regulatory Agency Approvals Declaration of Conformity Europe and 230 V CountriesCountries APC Contact Numbers and Support Limited WarrantyLife Support Policy Copyright and Trademark InformationSafety and General Information Japan Replacement Modules Model Number DescriptionAbout Your UPS EuropeExtended Run PowerDistribution OptionsFront View Component Identification Product OverviewRear View Component Identification UPS- Rear View SYPD3 installedMIM RIM System Block DiagramBasics Electrical Preparation Reminder ChecklistPurchase of System Site PreparationLbs kg Short-Term Battery Module Storage RequirementsWeights Length Width Height Measurements Inches cm Shipping & ReceivingThermal Dissipation Installation RequirementsPhysical Requirements Environmental RequirementsElectrical Requirements Remote Emergency Power Off RepoUnpacking Installing the UPSContents Moving the UPS to the Installation SiteInstallation Installing in a Four Post Rack Installation Installation Wiring the UPS Power Cord Ratings Switch Setting North AmericaJapan 200 Installation Installation Completing the Installation Installation Connecting Load Equipment to the UPS Final Installation Checklist Post Installation Procedures Replacing Battery ModulesReplacing Power Modules Replacing Intelligence Modules Operational Specifications Input SpecificationsTechnical Reference Output Specifications Physical SpecificationsCompliance Specifications APC Symmetra RM 4-12 kVA UPS Page Messages Table of Contents PowerView NavigationMenu Description Navigation Name Sound Function Keys FunctionsTurning on the UPS Powering Up the Load Equipment Powering Down the Load Equipment Bypass Operation Shown connected to Symmetra RM 2-6 kVA Language SettingTypical Programming Cable Getting Started Getting Started Menu Item Function Command ReferenceAccessories Menu Control MenuDisplay Function Options Display MenuDiagnostics Menu Help MenuLogging Menu Status Menu Menu Item Function Options Setup MenuUPS ID PowerView Message Meaning Corrective Action TroubleshootingMessages Meaning Corrective Action Messages PowerView Message Meaning Corrective Action Messages Service Maintenance

412 kVA, SYBT3 specifications

The APC SYBT3 412 kVA is a high-performance uninterruptible power supply (UPS) system designed to provide reliable power solutions for critical applications in various industries. Ideal for data centers, telecom infrastructures, and other mission-critical operations, the APC SYBT3 is engineered to deliver a robust power backup to prevent downtime.

One of the main features of the APC SYBT3 is its impressive capacity of 412 kVA. This high power output ensures that it can support large loads while maintaining stable operations even during power fluctuations. The system is designed to handle essential equipment, guaranteeing that your operations continue without interruption.

The APC SYBT3 utilizes advanced technologies to optimize performance and energy efficiency. This includes an intelligent battery management system that prolongs battery life while ensuring reliable energy delivery. The UPS is equipped with a modern inverter that efficiently converts DC battery power to AC power, enabling seamless transitions during power outages.

Another key characteristic of the APC SYBT3 is its modular design, which allows for easy integration into existing systems. This modularity supports scalability, enabling users to expand their power capacity as needed without significant infrastructure changes. This feature is particularly beneficial for organizations that anticipate growth or fluctuations in power requirements.

The APC SYBT3 also boasts superior communications features, including an advanced monitoring interface. This feature allows for real-time tracking of power parameters, battery health, and operational status, ensuring users can address potential issues before they escalate. Remote monitoring capabilities enable IT personnel to manage the UPS from anywhere, enhancing operational efficiency.

In addition to its robust power performance, the APC SYBT3 offers a compact footprint, making it suitable for environments where space is limited. This design consideration ensures that large power needs can be met without sacrificing valuable real estate.

Overall, the APC SYBT3 412 kVA UPS represents a blend of advanced engineering, efficient power management, and user-friendly features. Its ability to provide seamless power continuity makes it an indispensable asset for organizations seeking to safeguard their critical operations against power interruptions.
Top Page Image Contents