To Operate The PowerCharger with DDM

The standard test is adequate for virtually all conditions to verify the capacity of the battery before taking it into the field. The 24 hour test need only be performed on a battery, typically an older one (2 years or more), which may have exhibited questionable performance.

Note: The DDM test mode should be used sparingly. Remember that a cycle performed in test is part of the battery’s overall life. Anton/Bauer suggests that a typical management routine for your batteries might be to test them once every 90 days during the first two years and every 60 days thereafter. If a record is kept of the battery’s performance on test, any anomaly will become apparent from the record. It is not necessary to fully discharge an Anton/Bauer battery before recharging. The PowerCharger’s charging routines and the high voltage design of the Anton/Bauer batteries precludes the problems which old 12 volt batteries had in the past. Don’t waste battery life on unnecessary testing.

To Operate The PowerCharger with DDM

1.Mount the battery to any position on the PowerCharger. When the PowerCharger has completed its communication with the battery, the ALTERNATING RED and GREEN LEDs will stop and the battery will begin its charge routine. The battery information and position number will appear on the LCD display. (If the battery is already on the charger, press the DISPLAY button until the position for the battery to be tested is displayed.)

2.Press the TEST button on the front panel of the PowerCharger. An audible alert will be heard and the LCD will display “HOLD TEST BUTTON 3 SECONDS TO SELECT A TEST”.

3.Hold the TEST button as the unit beeps 3 times. Release the button and the unit will indicate that the test mode has been selected. This Standard test will charge-discharge- charge the battery. Testing time is approximately 6-8 hours per battery.

4.The PowerCharger will ask if the 24 hour test is desired. If so, press the TEST button again to select this test. If not, the PowerCharger will automatically begin the standard test. A 24 Hour Test will charge the battery, let the battery sit for a 24 hour period, test the battery and then charge the battery. This test will determine how much capacity the battery will lose over a 24 hour period, when not being used.

The “RS-232 Accessory Port” on the PowerCharger transmits test information in ASCII format to any serial communications capable device, such as a terminal emulator or printer. A personal computer serial port can also be connected and by employing any number of communications applications (such as PROCOMM, or Windows “Terminal”) test data can be saved in file format as a permanent record of battery performance.

A serial data capable printer can be attached to the PowerCharger at the “RS-232 Accessory Port”, enabling the printout of hard copy of performance data from a tested battery. The following is a partial list of printer manufacturer models which are compatible with the PowerCharger:

•Okidata ML 184 Turbo

•Okidata ML 395

•Panasonic KX-P3200

Printers should be set for 1200 baud, 8 bit data length, one start bit, one stop bit. Consult the printer’s owners’ manual for setup instructions.

DUAL 2702, QUAD 2702 specifications

Anton/Bauer is a leading name in battery technology, especially renowned for its line of professional camera batteries and chargers. Among its standout products are the QUAD 2702 and DUAL 2702 battery chargers, specifically designed for the demanding needs of the broadcast and film industries. Both models provide reliable charging solutions to keep your camera equipment powered throughout rigorous shooting schedules.

The Anton/Bauer QUAD 2702 is a sophisticated four-position charger that caters to multiple battery types, including Gold Mount and V-Mount batteries. One of its primary features is the ability to charge two batteries at a time, significantly enhancing workflow efficiency. The charger uses advanced smart charging technology that automatically detects the chemistry of the attached batteries, optimizing the charging process for maximum performance and longevity.

Built with durability in mind, the QUAD 2702 features a rugged casing that withstands the rigors of on-set use. Additionally, its integrated LED indicators display the charging status of each battery, allowing users to monitor multiple batteries at a glance.

The DUAL 2702, while similar in many ways to its quad counterpart, offers charging capabilities for two batteries simultaneously. This makes it an ideal choice for smaller production teams or operators who might not require the full capacity of the QUAD model. Like the QUAD 2702, it also features an advanced charging algorithm that maximizes battery life, ensuring that professional videographers get the most out of their investment.

Both chargers are designed with versatility in mind. They are compatible with a wide range of Anton/Bauer batteries, making them an essential tool for any filmmaker or photographer. The DUAL and QUAD 2702 units also come equipped with a power supply circuit that can handle a wide range of input voltages, allowing them to be used in various locations around the world without issue.

In summary, the Anton/Bauer QUAD 2702 and DUAL 2702 battery chargers represent the pinnacle of professional battery charging solutions. With their robust construction, advanced charging technologies, and user-friendly design, they are invaluable assets for any audio-visual production team. Whether you're shooting on location or in a studio, these chargers ensure your equipment remains powered, allowing you to focus on what matters most: capturing stunning visuals.