General Safety Rules

!	WARNING	“READ ALL INSTRUCTIONS” Failure to follow the safety rules listed below and other basic safety precautions
		may result in serious personal injury.

THINK SAFETY Safety is a combination of operator common sense and alertness at all times when the X-Bench is being used.

Work Area

KEEP CHILDREN AWAY

Do not let visitors contact tool or extension cord. All visitors should be kept away from work area.

KEEP WORK AREAS CLEAN

Cluttered areas and benches invite accidents.

MAKE WORKSHOP CHILD-PROOF

With padlocks, master switches.

AVOID DANGEROUS ENVIRONMENTS

Don’t use power tools in damp or wet locations. Keep work area well lit. Do not expose power tools to rain. Do not use tool in presence of flammable liquids or gases.

Personal Safety

KNOW YOUR POWER TOOL

Read and understand the owner’s manual and labels affixed to the tool. Learn its application and limitations as well as the specific potential hazards peculiar to this tool.

DON’T OVERREACH

Keep proper footing and balance at all times.

STAY ALERT

Watch what you are doing. Use common sense. Do not op- erate tool when you are tired. Do not operate while under medication or while using alcohol or other drug.

DRESS PROPERLY

To avoid being pulled into a blade, do not wear loose clothing, loose fitting gloves, necktie or jewelry. Tie back long hair or wear protective hair covering and roll long sleeves above the elbow. Rubber gloves and non-skid footwear are recommended when working outdoors.

USE SAFETY GOGGLES

Use safety goggles (head protection). Wear safety goggles (must comply with ANSI Standard Z87.1) at all times. Wear non-slip footwear and a hard hat, if appropriate. Also, use face or dust mask if cutting operation is dusty, and ear protectors (plugs or muffs) during extended periods of operation.

GUARD AGAINST ELECTRIC SHOCK

Prevent body contact with grounded surfaces. For example: pipes, radiators, ranges, refrigerator enclosures.

DISCONNECT TOOL FROM POWER SOURCE

When not in use, before servicing, when changing blades, bits, cutters, etc.

KEEP GUARDS IN PLACE

In working order, and in proper adjustment and alignment.

REMOVE ADJUSTING KEYS AND WRENCHES

When not in use, before servicing, when changing blades, bits, cutters, etc.

AVOID ACCIDENTAL STARTING

Make sure the switch is in the “OFF” (“O”) position before plugging in tool.

NEVER STAND ON TOOL OR ITS STAND

Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do not store materials on or near the tool such that it is necessary to stand on the tool or its stand to reach them.

CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, mounting and any other condi- tions that may affect its operation. A guard or other part that is damaged should be properly replaced.

ALL REPAIRS, ELECTRICAL OR MECHANICAL, SHOULD bE ATTEMPTED ONLY bY TRAINED REPAIRMEN.

Contact the nearest Skil Factory Service Center, Authorized Service Station or other competent repair service.

USE ONLY SKIL REPLACEMENT PARTS;

Any others may create a hazard.

THE USE OF ANY OTHER ACCESSORIES NOT SPECI- FIED IN THE CURRENT SKIL CATALOG MAY CREATE A HAzARD.

Tool Use

DON’T FORCE TOOL

It will do the job better and safer at the rate for which it was designed.

USE THE RIGHT TOOL

Don’t force small tool or attachment to do the job of a heavy- duty tool. Don’t use tool for purpose not intended — for ex- ample; don’t use circular saw for cutting tree limbs or logs.

SECURE WORK

Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate the tool.

DIRECTION OF FEED

Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

NEVER LEAVE TOOL RUNNING UNATTENDED

Turn power off. Don’t leave tool until it comes to a complete stop. Be aware of the location and setting of the switch “ON" position. Never leave the switch in the “ON” position. Be aware of switch location and know how to shut off the tool in emergency situations. Accidental start-ups could cause injury.

DON’T AbUSE THE CORD

Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

Tool Care

DO NOT ALTER OR MISUSE TOOL

These tools are precision built. Any alteration or modification not specified is misuse and may result in dangerous conditions.