Festool MFT/KAPEX, MFT/3 instruction manual Setting up Guide rail support, Front Working side

Page 6

REAR

4-5

4-1

4-2 4-3

FRONT ( Working side)

Adjust the speed of the saw [3-2] to a setting of „6“ (maximum speed). Set the depth of cut, using the depth stop adjust- ment [3-1], to 8 mm (5 mm for the thick- ness of the guide rail plus 3 mm cutting depth) and cut the splinter guard along the full length without interruption.

For trimming the splinter guard it is best to use some sort of backing piece, such as plywood or fiberboard.

The edge of the splinter guard now corre- sponds exactly to the cutting edge.

Step 3: Setting up the

guide rail support

The table comes from the factory with two stops [4-2, 4-4] pre-set on the long sides of the profile frame, opposite each other. These are recommended working positions

4-4for the support unit [4-2] and swivel unit [4-4].

 

NOTE: During transport it is possible that

 

the set screws holding the stops may have

 

loosened. If this is the case, you will have

 

to position and retighten the registering

 

stops. Facing the front of the table, the

 

measurement is 8 3/4’’ from the side face

 

of the profile frame at the right side of the

 

table. Facing the rear, the stop is approxi-

 

mately 7 2/3’’ from the side face at the left

4

side of the table.

The swivel unit [4-4] is mounted on the

 

 

rear long side, the support unit [4-2] on

 

the front side.

Both units are inserted into the profile groove from the left up to the stops with the height adjustment [4-2] and the rota- ry knob [4-1] released, and then clamped with the rotary knob [4-1].

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Guide d’utilisation Manual de instruccionesPage Table of Contents Technical dataSymbols DesignIntended use MFT/3 Setting up and assembly Setting upTrim splinter guard Setting up Guide rail support Front Working sideAttaching the pre-set Profile setting rail Attaching the guide railAdjusting the pre-set Profile setting rail Calibrating angleAdjustment at right angles to Bench edge Adjusting the guide rail Relation to the workpieceAdjustment parallel to the bench edge Adjusting the stop ruler LengthwaysMounting the Kapex MaintenanceAccessories, tools Turning the perforated topWarranty Conditions of 1+2 Warranty Festool Limited WarrantyPage La poussière, un ris Table des matièresCaractéristiques techniques Que pour la santéUtilisation conforme1-4aux Prescriptions SymbolesEléments fournis MFT/3Installation et montage Etape 1 InstallationEtape 2 Sciage du pare-éclats Etape 3 Mis en place des fixations du rail de guidageEtape 5 Montage de la guide Butée angulaire Etape 6 Réglage de la Butée angulaireDécalage perpendiculairement par Décalage parallèlement par rapportAu bord de la table Rapport au bord de la tableEtape 8 Réglage du rail de gui Dage par rapport à la pièce Décalage de la règle de butée Dans le sens longitudinalDécalage angulaire à laide de Léchelle graduée Installation de loutil Kapex Accessoires, outilsRetournement de la plaque Trouée Garantie Conditions de la ga Rantie 1+2 ans Garantie limitée de FestoolPage Riesgos para la salud pro ContenidoDatos técnicos Ducidos por el polvoSímbolos Dotación de suministroUso conforme a lo previsto MFT/3 Instalación y montaje Paso 1 InstalaciónPaso 2 Serrar la protección an Ti-astillas Paso 3 Fijar los soportes para El riel de guía Parte posterior DelantePaso 4 Fijar el riel de guía Paso 5 Montaje del tope angu Lar escalonadoPaso 6 Ajustar el tope angular Paso 7 Ajuste del tope angular Escalonado Paso 8 Ajuste del riel de guía a La pieza de trabajoInstalación de la Kapex MantenimientoReverso de la placa perforada Accesorios, herramientas Garantía Condiciones de la Ga Rantía 1 +Garantía limitada de Festool

MFT/3, MFT/KAPEX specifications

The Festool MFT/KAPEX and MFT/3 represent a harmonization of craftsmanship, precision, and versatility designed specifically for woodworking professionals and enthusiasts alike. These multifunctional tables are not merely work surfaces; they are engineered tools that enhance the entire woodworking experience.

The MFT/KAPEX is a portable, multi-functional work table designed to work seamlessly with the KAPEX mitre saw. One of its standout features is the integrated guide rail system, which allows for precise cuts and efficient handling of large materials. The table is equipped with a clamping system that secures workpieces, ensuring stability and accuracy during cutting operations. Another key characteristic is its foldable design, enabling easy transport and storage, making it ideal for job-site use.

In contrast, the MFT/3 serves as a highly versatile workbench that accommodates various tasks beyond sawing. Its dual-surface work area consists of a perforated top, providing an expandable working area with integrated clamping points. This feature allows for effortless and secure attachment of workpieces, making it suitable for various applications including sanding, routing, and assembly. The MFT/3 also boasts a robust construction, ensuring durability and prolonged use under professional conditions.

Both tables are equipped with the Festool Precision and reliability that the brand is known for, including features such as the guide rail that allows for flawless longitudinal cuts and an adjustable height for user comfort. The tables utilize a combination of high-quality materials that guarantee stability and ease of maneuvering.

Additionally, the MFT/KAPEX and MFT/3 embrace advanced technology with features like the FastFix system for quick changeovers of accessories and the option to integrate with Festool’s dust extraction systems, promoting a cleaner work environment and improved health safety for users.

These multifunction tables embody Festool’s commitment to innovation, meeting the diverse needs of the modern woodworker. Whether you are a professional contractor on a job site or a dedicated hobbyist in your workshop, the MFT/KAPEX and MFT/3 deliver unmatched versatility and precision, enabling you to achieve exceptional results in your woodworking projects.
Top Page Image Contents