Porter-Cable 28-475X, 28-248 instruction manual Stay ALERT, Watch What YOU are Doing

Page 3

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1.FOR YOUR OWN SAFETY, READ THE INSTRUCT- TION MANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations, and specific hazards will greatly minimize the possibility of accidents and injury.

2.USE CERTIFIED SAFETY EQUIPMENT. Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment should comply with ANSI S3.19 standards, and dust mask protection should comply with MSHA/NIOSH certified respirator standards. Splinters, air-borne debris, and dust can cause irritation, injury, and/or illness.

3.DRESS PROPERLY. Do not wear tie, gloves, or loose clothing. Remove watch, rings, and other jewelry. Roll up your sleeves. Clothing or jewelry caught in moving parts can cause injury.

4.DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placing arms, hands, and fingers in danger.

5.MAINTAIN ALL TOOLS AND MACHINES IN PEAK CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and machines can further damage the tool or machine and/or cause injury.

6.CHECK FOR DAMAGED PARTS. Before using the machine, check for any damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, and any other conditions that may affect its operation. A guard or any other part that is damaged should be properly repaired or replaced. Damaged parts can cause further damage to the machine and/or injury.

7.KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.

8.KEEP CHILDREN AND VISITORS AWAY. Your shop is a potentially dangerous environment. Children and visitors can be injured.

9.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.

10.USE THE GUARDS. Check to see that all guards are in place, secured, and working correctly to prevent injury.

11.REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING THE MACHINE. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.

12.USE THE RIGHT MACHINE. Don’t force a machine or an attachment to do a job for which it was not designed. Damage to the machine and/or injury may result.

13.USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recom- mended by Delta may cause damage to the machine or injury to the user.

14.USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. See the Extension Cord Chart for the correct size depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

15.SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury.

16.FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out a high speed.

17.DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result.

18.DON’T OVERREACH. Loss of balance can make you fall into a working machine, causing injury.

19.NEVER STAND ON THE MACHINE. Injury could occur if the tool tips, or if you accidentally contact the cutting tool.

20.NEVER LEAVE THE MACHINE RUNNING UNATTEN- DED. TURN THE POWER OFF. Don’t leave the machine until it comes to a complete stop. A child or visitor could be injured.

21.TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE POWER SOURCE before installing or removing accessories, before adjusting or changing set-ups, or when making repairs. An accidental start-up can cause injury.

22.MAKE YOUR WORKSHOP CHILDPROOF WITH PADLOCKS, MASTER SWITCHES, OR BY REMOVING STARTER KEYS. The accidental start-up of a machine by a child or visitor could cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING,

AND USE COMMON SENSE. DO NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power tools may result in injury.

24.THE DUST GENERATED by certain woods and wood products can be injurious to your health. Always operate machinery in well-ventilated areas, and provide for proper dust removal. Use wood dust collection systems whenever possible.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Wood Cutting Band Saw Important Safety Instructions Safety Guidelines DefinitionsStay ALERT, Watch What YOU are Doing Additional Safety Rules For Band Saws Power Connections Functional Description Unpacking and Cleaning Band SAW Parts Do not Completely Tighten the Bolt and NUT AT this Time AssemblyMotor Bracket To Stand Motor to Motor BracketDust Chute TOP Plate to StandHinge Catch a is Pointed UP AS Shown in FIG Stand Door to StandDust Port Only be Attached with the TWO Bottom Holes in the StandCompletely Tighten the Screws AT this Time Hinge Opening is Pointing DownIs on the Side of the Stand with the Belt Opening B SAW to StandMotor Pulley Belt to SAW and Motor PulleySure the Slot C , in the Table is Facing Away from the ARM D Table to SAWBlade to SAW Table InsertLength Blades On / OFF Switch To Stand Make Sure That the Motor Plug Operating Controls and AdjustmentsLocking Switch in the OFF Position Starting Stopping SAWAdjusting Table Stops Disconnect Machine from Power SourceTilting the Table To set the adjustable stops Adjusting Blade TensionVertical Adjustment of the Upper Blade Guide Assembly Tracking the BladeNever Track the Blade While Tool is Running Adjusting the Upper Blade Guides and Blade Support Bearing Adjusting Lower Blade Guides and Blade Support Bearing OperationsCutting Curves Probable Cause Remedy Troubleshooting GuideTrouble Blade will not Track Band SAW Blades Page PARTS, Service or Warranty Assistance AccessoriesCanadian PORTER-CABLE Delta Service Centers

28-475X, 28-248 specifications

The Porter-Cable 28-248 and 28-475X are two impressive models from Porter-Cable, a brand known for its high-quality power tools that cater to the needs of both professionals and DIY enthusiasts. These models are designed to deliver reliable performance, durability, and innovative features suitable for a wide range of applications.

The Porter-Cable 28-248 is a 28-gauge pneumatic brad nailer. This tool is compact and lightweight, making it easy to maneuver in tight spaces. One of its standout features is the tool-free depth of drive adjustment, allowing users to modify the depth of the nails without additional tools. This is particularly useful when working with different materials or when precision is paramount.

The 28-248 is equipped with a rear exhaust that directs air away from the user, keeping the workspace clean and enhancing comfort during operation. The integrated power adjustment dial lets users adjust the power depending on the material being used, providing versatility across various projects. Additionally, the 28-248 features a reload indicator that signals when it's time to refill the magazine, preventing interruptions during work.

On the other hand, the Porter-Cable 28-475X is a more robust option designed for industrial applications. It is a 27-gauge nail gun that offers a higher capacity magazine for less downtime. The 28-475X features a stainless steel magazine that ensures durability and smooth operation while reducing the risk of jams.

This model also includes a selective actuation switch, allowing users to choose between sequential and contact firing modes based on their needs. The built-in dry fire lockout mechanism is another valuable feature that prevents the tool from firing without nails, which prolongs its lifespan and ensures safety.

The ergonomic design of both models emphasizes user comfort, with features like rubber grips that minimize fatigue during prolonged use. Both tools are compatible with a variety of nail sizes and types, making them suitable for a range of tasks from cabinetry to flooring installations.

In summary, the Porter-Cable 28-248 and 28-475X stand out for their innovative features, ergonomic designs, and flexibility in application. Whether you're a contractor or a DIY hobbyist, both models offer the durability and performance needed to tackle any job efficiently.
Top Page Image Contents