Porter-Cable 28-248, 28-475X instruction manual Band SAW Parts

Page 8

BAND SAW PARTS

1

2

A

6

7

8

 

 

 

 

 

 

9

11

 

 

 

12

 

10

 

 

 

13

14

 

 

 

15

 

19

24

 

 

3

4

5

Fig. 4

16

 

20

 

25

 

 

27

 

 

 

 

 

 

 

 

 

 

21

 

 

 

 

 

17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

 

 

 

 

 

 

 

 

 

 

 

18

26

 

 

28

 

 

 

23

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 5

1.

Saw

15.

5/16-18x1½" Hex Head Screw (4)

2.

Stand

16.

5/16-18x3/4" Carriage Head Bolt (16)

3.

Dust Chute

17.

#10-24x1/2" Socket Head Cap Screw (8)

4.

Top Plate

18.

#10-32x1/2" Pan Head Screw (4)

5.

Stand Door

19.

5/16" Flat Washer (4)

6.

Motor and key (A)

20.

7/16" Jam Nut (2)

7.

Table

21.

7/16" Locknut (2)

8.

Belt

22.

5/16-18 Hex Nut (20)

9.

On/Off Switch

23.

#10-32 Hex Nut (4)

10

Motor Bracket (2)

24.

Table Handle (2)

11.

Dust Spout

25.

Hinge Catch (2)

12.

Blade

26.

Door Latch

13.

Table Insert

27.

Hinge (2)

14.

Motor Pulley

28.

Cord Bushing

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents
Wood Cutting Band Saw Safety Guidelines Definitions Important Safety InstructionsStay ALERT, Watch What YOU are Doing Additional Safety Rules For Band Saws Power Connections Functional Description Unpacking and Cleaning Band SAW Parts Assembly Motor Bracket To StandMotor to Motor Bracket Do not Completely Tighten the Bolt and NUT AT this TimeTOP Plate to Stand Dust ChuteStand Door to Stand Dust PortOnly be Attached with the TWO Bottom Holes in the Stand Hinge Catch a is Pointed UP AS Shown in FIGHinge Opening is Pointing Down Completely Tighten the Screws AT this TimeSAW to Stand Motor PulleyBelt to SAW and Motor Pulley Is on the Side of the Stand with the Belt Opening BTable to SAW Sure the Slot C , in the Table is Facing Away from the ARM DLength Blades Blade to SAWTable Insert On / OFF Switch To Stand Operating Controls and Adjustments Locking Switch in the OFF PositionStarting Stopping SAW Make Sure That the Motor PlugTilting the Table Adjusting Table StopsDisconnect Machine from Power Source Adjusting Blade Tension To set the adjustable stopsNever Track the Blade While Tool is Running Vertical Adjustment of the Upper Blade Guide AssemblyTracking the Blade Adjusting the Upper Blade Guides and Blade Support Bearing Cutting Curves Adjusting Lower Blade Guides and Blade Support BearingOperations Troubleshooting Guide Probable Cause RemedyTrouble Blade will not Track Band SAW Blades Page Accessories PARTS, Service or Warranty AssistanceCanadian PORTER-CABLE Delta Service Centers
Top Page Image Contents