Porter-Cable 28-248, 28-475X instruction manual Additional Safety Rules For Band Saws

Page 4

ADDITIONAL SAFETY RULES

FOR BAND SAWS

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1.DO NOT OPERATE THIS MACHINE UNTIL it is assembled and installed according to the instructions.

2.OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not familiar with the operation of this tool.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, properly adjusted, secured, and working correctly.

5.USE PROPER BLADE SIZE and type.

6.ADJUST THE UPPER BLADE GUIDE so that it is about 1/8" above the workpiece.

7.PROPERLY ADJUST the blade tension, tracking, blade guides, and blade support bearings.

8.KEEP ARMS, HANDS, AND FINGERS away from the blade.

9.AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause a hand to move into the blade.

10.NEVER START THE MACHINE before clearing the table of all objects (tools, scrap pieces, etc.).

11.NEVER START THE MACHINE with the workpiece against the blade.

12.HOLD WORKPIECE FIRMLY against the table. DO NOT attempt to saw a workpiece that does not have a flat surface against the table.

13.HOLD WORKPIECE FIRMLY and feed into blade at a moderate speed.

14.NEVER REACH UNDER THE TABLE while the machine is running.

15.TURN THE MACHINE “OFF” to back out of an uncompleted or jammed cut.

16.MAKE “RELIEF” CUTS prior to cutting long curves.

17.TURN THE MACHINE “OFF” and wait for the blade to stop prior to cleaning the blade area, removing debris near the blade, removing or securing workpiece, or changing the angle of the table. A coasting blade can be dangerous.

18.NEVER PERFORM LAYOUT, ASSEMBLY, or set- up work on the table/work area when the machine is running.

19. TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

20.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

21.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Wood Cutting Band Saw Safety Guidelines Definitions Important Safety InstructionsStay ALERT, Watch What YOU are Doing Additional Safety Rules For Band Saws Power Connections Functional Description Unpacking and Cleaning Band SAW Parts Assembly Motor Bracket To StandMotor to Motor Bracket Do not Completely Tighten the Bolt and NUT AT this TimeTOP Plate to Stand Dust ChuteStand Door to Stand Dust PortOnly be Attached with the TWO Bottom Holes in the Stand Hinge Catch a is Pointed UP AS Shown in FIGHinge Opening is Pointing Down Completely Tighten the Screws AT this TimeSAW to Stand Motor PulleyBelt to SAW and Motor Pulley Is on the Side of the Stand with the Belt Opening BTable to SAW Sure the Slot C , in the Table is Facing Away from the ARM DTable Insert Blade to SAWLength Blades On / OFF Switch To Stand Operating Controls and Adjustments Locking Switch in the OFF PositionStarting Stopping SAW Make Sure That the Motor PlugDisconnect Machine from Power Source Adjusting Table StopsTilting the Table Adjusting Blade Tension To set the adjustable stopsTracking the Blade Vertical Adjustment of the Upper Blade Guide AssemblyNever Track the Blade While Tool is Running Adjusting the Upper Blade Guides and Blade Support Bearing Operations Adjusting Lower Blade Guides and Blade Support BearingCutting Curves Troubleshooting Guide Probable Cause RemedyTrouble Blade will not Track Band SAW Blades Page Accessories PARTS, Service or Warranty AssistanceCanadian PORTER-CABLE Delta Service Centers

28-475X, 28-248 specifications

The Porter-Cable 28-248 and 28-475X are two impressive models from Porter-Cable, a brand known for its high-quality power tools that cater to the needs of both professionals and DIY enthusiasts. These models are designed to deliver reliable performance, durability, and innovative features suitable for a wide range of applications.

The Porter-Cable 28-248 is a 28-gauge pneumatic brad nailer. This tool is compact and lightweight, making it easy to maneuver in tight spaces. One of its standout features is the tool-free depth of drive adjustment, allowing users to modify the depth of the nails without additional tools. This is particularly useful when working with different materials or when precision is paramount.

The 28-248 is equipped with a rear exhaust that directs air away from the user, keeping the workspace clean and enhancing comfort during operation. The integrated power adjustment dial lets users adjust the power depending on the material being used, providing versatility across various projects. Additionally, the 28-248 features a reload indicator that signals when it's time to refill the magazine, preventing interruptions during work.

On the other hand, the Porter-Cable 28-475X is a more robust option designed for industrial applications. It is a 27-gauge nail gun that offers a higher capacity magazine for less downtime. The 28-475X features a stainless steel magazine that ensures durability and smooth operation while reducing the risk of jams.

This model also includes a selective actuation switch, allowing users to choose between sequential and contact firing modes based on their needs. The built-in dry fire lockout mechanism is another valuable feature that prevents the tool from firing without nails, which prolongs its lifespan and ensures safety.

The ergonomic design of both models emphasizes user comfort, with features like rubber grips that minimize fatigue during prolonged use. Both tools are compatible with a variety of nail sizes and types, making them suitable for a range of tasks from cabinetry to flooring installations.

In summary, the Porter-Cable 28-248 and 28-475X stand out for their innovative features, ergonomic designs, and flexibility in application. Whether you're a contractor or a DIY hobbyist, both models offer the durability and performance needed to tackle any job efficiently.
Top Page Image Contents