Powermatic 2013, 2415 Upper Blade Guide Assembly, Upper Blade Guides and Upper Support Bearing

Page 18

Upper Blade Guide Assembly

1.Disconnect machine from power source.

2.Loosen lock knob (see B, Figure 14) and raise or lower upper blade guide assembly by turning the handwheel (C, Figure 14).

3.Position the blade guide assembly about 3/16” above the material to be cut. The scale (J, Figure 14) shows the distance from bottom of upper blade guides to the table surface.

4.Tighten lock knob (B, Figure 14).

Upper Blade Guides and Upper

Support Bearing

To adjust the bearing guides for proper blade control, proceed as follows.

1.Disconnect machine from power source.

2.Blade must already be tensioned and tracking properly.

3.Loosen the locking handle (A, Figure 17).

4.Adjust the guide bracket (B, Figure 17) by rotating knob (G, Figure 17) until the front of the guide bearings (C, Figure 17) are just behind the blade’s gullet (curved area at the base of the tooth). See Figure 18.

5.Tighten the locking handle (A, Figure 17).

6.Loosen set screw (D, Figure 17) on the guide bearing assembly, with a 3mm hex wrench. (Figure 17 shows the set screw for the right hand bearing; the set screw for the left hand bearing is shown in Figure 19.)

7.The guide bearing rotates on an eccentric shaft. Adjust the guide bearing, by rotating the knob (H, Figure 19) until the guide bearing rests lightly against the blade. Do not force the guide bearing against the side of the blade.

8.Tighten set screw (D, Figure 17).

9.Repeat the process for the other guide bearing. After adjustment, make sure the set screw (D, Figure 19) is tightened.

10.Loosen nut (E, Figure 19).

11.Adjust the support bearing using the knob (F, Figure 19) until the space between the support bearing and the back edge of the blade is approximately 1/64”. A convenient way to achieve this spacing is by placing a dollar bill folded twice (four thicknesses of a dollar bill is approximately 1/64”) between blade and support bearing.

18

Figure 17

Figure 18

Figure 19

Image 18
Contents Vantage Drive Elgin, Illinois Revision C 8/06Copyright WMH Tool Group Warranty and Service More InformationTable of Contents Electrical Connections Page Page Introduction Specifications Features and Terminology Model 2415 shownContents of the Shipping Container UnpackingAssembly Installing Fence and RailsPage Grounding Instructions Dust CollectionVolt, Single Phase Operation Volt, Three Phase OperationExtension cords Converting from 230 Volt to 460 Volt Three Phase Only Three-Phase Test RunAdjustments Table TiltTable Stop Installing/Changing Blades Blade TensionBlade Tracking Upper Blade Guide Assembly Upper Blade Guides and Upper Support BearingLower Blade Guides and Lower Support Bearing Miter Gauge Belt TensionBlade Speed Adjustment Operating ControlsBelt Alignment Brake Pedal General ProcedureOperation RippingCrosscutting ResawingBlade Lead Blade Selection Width PitchShape Set MaterialBlade Breakage Maintenance Tire ReplacementBand Wheel Replacement Blade Selection Guide For Radius CuttingTroubleshooting Operational Problems Trouble Troubleshooting Mechanical and Electrical Problems Verify machine is connected to powerReplacement Parts Trouble Probable Cause RemedyParts List Saw Body Assembly 2013 Band Saw Parts List Saw Body Assembly 2415 Band Saw Saw Body Assembly 2013 Parts List Table Assembly 2013 Band Saw TS-0270051 2013-253TS-0051061 TS-0270061Parts List Table Assembly 2415 Band Saw Index No. Part No Description Size Qty Table Assembly 2013 Parts List Upper Wheel Base Assembly 2013 Band Saw Parts List Upper Wheel Base Assembly 2415 Band Saw Upper Wheel Base Assembly 2013 Parts List Lower Wheel Base Assembly 2013 Band Saw TS-081C032 Parts List Lower Wheel Base Assembly 2415 Band Saw 2415-4262415-426RC Index No. Part No Description Size Qty Lower Wheel Base Assembly 2013 Parts List Guide Bracket Assembly 2013 Band Saw 2013-567 Parts List Guide Bracket Assembly 2415 Band Saw Index No. Part No Description Size Qty Guide Bracket Assembly 2013 Page Page Electrical Connections 230 Volt, 3 Phase Models 2013 Electrical Connections 460 Volt, 3 Phase Models 2013 Page Page WMH Tool Group