Multiquip TP24X manual Blade Installation, See for proper blade use guidelines

Page 19

set-up

Blade Installation

Refer to Figure 9 and the following instructions for installing the blade.

1.Loosen blade guard adjustment knob located at the rear of the blade guard. Carefully raise the cutting head to its highest position and secure it into place by tightening the blade guard adjustment knob.

2.Remove the blade shaft nut and outer flange. If a blade has been mounted, hold the blade with one hand and use the other hand to loosen the nut with the universal wrench. Remove existing blade.

3.Mount new blade, but make certain the arrow on the blade coincides with the rotation direction of the shaft. Ensure the capacity of the blade guard matches the diameter of your cutting blade.

4.Attach outer flange and blade shaft nut. Hold the blade with one hand and use the other hand to tighten the nut with the universal wrench. Make certain the flanges are pressed flush against the blade and that the nut is firmly tighthened, but do not over tighten.

5.Loosen blade guard adjustment knob, lower the blade guard, and retighten the knob.

6.Slightly loosen the cutting head adjustment knob, lower the cutting head so that the blade is 1/4" (6 mm) below the surface of the cutting table.Tighten the adjustment knob firmly to hold the cutting head in place.

BLADE

GUARD BLADE

GUARD

ADJUSTMENT

KNOB

OUTER

BLADEFLANGE

SHAFT

INNER

BLADE

SHAFT NUT

FLANGE

 

BLADE

Figure 9. Blade Installation

See Table 5 for proper blade use guidelines.

Table 5. Proper Blade Use

Dos

Don’ts

 

 

Inspect blades daily for cracks or uneven wear.

Do not operate the saw without safety guards in place.

 

 

Always use appropriate blades for material being cut.

Do not operate the saw with blades larger than 10

in. (254 mm)

 

 

 

Inspect arbor shaft for uneven wear before mounting

Do not cut dry with blades marked “Use Wet”.

blade.

 

Always use blades with the correct arbor shaft size.

Do not exceed manufacturer’s recommended

maximum RPM.

 

 

 

Ensure that blade is mounted in the correct

Do not force blade into material. Let blade cut at its

direction.

own speed.

 

 

Use proper safety equipment when operating the saw.

Do not make long cuts with dry blades. Allow them

to air cool.

 

 

 

Always have a continuous flow of water on both

Do not use the edge or side of blade to cut or grind.

sides of blade.

 

 

 

Secure the blade to the arbor with a wrench.

Do not attempt to cut a radius or curve.

 

 

Inspect segment blades for segment cracking or loss.

Do not cut too deep or too fast into the material.

 

 

Do not use damaged blades.

Do not cut any material not recommended by blade

manufacturer.

 

 

 

TP24X TILE SAW • operation and parts manual — rev. #2 (04/12/12) — page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model TP24X Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsTP24X Tile Saw Table of ContentsChoose from three easy options SaFeTy meSSageS Safety InformationGeneraL SaFeTy BLade SaFeTy SaW SaFeTyTranSporTIng SaFeTy ELeCTrIC moTor SaFeTyPower Cord/Cable Safety LIFTIng SaFeTy3200 SpecificationsDimensions DimensionsDry Cutting Applications Accessories/Replacement PartsFeatures General informationTP24X Tile SAW operation and parts manual rev. #2 04/12/12 Saw Components Saw componentsStopper Place stopper in water tray when filling with water Saw set-up Support Stand Assembly OptionalElectric motor components/set-up Electric Motor ComponentsRear drip tray installation Water Pump AssemblySet-up Blade Components BladesCutting Depth See for proper blade use guidelines Blade InstallationNever grab or touch a live Power cord with wet hands, Connecting the PowerSawing Guides Using the Cutting Table Place the power ON/OFF switch in the OFF position downPerforming Diagonal Cuts Using the Drip GuardSawing guides Performing Straight CutsOperation Start-up ProcedureWait for the cutting blade to stop rotating Shut down ProcedureInspect the cutting table periodically. Replace worn parts Basic MaintenanceAfter not using the machine for a prolonged period of time Maintenance intervalsAfter wet cleaning and before using the machine again Before not using the machine for a prolonged period of timeBelt replacement Water pump maintenanceTake off the old belt and replace with new belt Bearing Housing Installation Bearing housing removalForth. If the table binds against the rail at any Realignment MethodIntially, but shifts apart as the table travels along Rail, proceed to MethodShim may be required Further adjustment-repeat stepMethod Table from the guide rails. See FigureTransporting the saw Leveling AdjustmentElectric Motor Wiring Diagram Wiring diagram electric motorBlade Troubleshooting Troubleshooting bladeSaw Troubleshooting Troubleshooting SawExplanation of Code in Remarks Column Tp24x tile saw with electric motor 1 to 3 units Suggested Spare PartsMain SAW Assy Part Name Cutting Head Assy Part Name QTY Remarks Cutting table assy Cutting table assy Blade guard assy Remarks Bearing housing assy Bearing housing assy Switch Box assy Includes items w/@ Tools and accessories TPS100034 OptionalTP100102 FreIgHT poLICy Terms and Conditions of Sale PartsTP24X Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help
Top Page Image Contents