Multiquip TP24X manual Stopper Place stopper in water tray when filling with water

Page 15

saw components

Figure 2 shows the location of the basic components of the TP24X saw. Listed below is a brief explanation of each component.

1.ACPowerCord — Plug this cord into a 125VAC receptacle when starting of the electric motor is required.

2.V-belt Cover — Remove this cover to access the drive V-belt. NEVER operate the saw with the V-belt cover removed

3.Rubber Splash Guard — Keeps water from splashing from the blade.

4.Electric Motor — This unit uses a 115V, 60 Hz, 1-1/2 HP electric motor.

5.Overcurrent Breaker Button — When a thermal overload condition exists, press this button to reset the breaker. Allow time for the electric motor to cool down before reseting the breaker.

6.Cutting Blade — This unit uses a 10-inch (254 mm) premium diamond blade. Always use recommended Multiquip cutting blades. When mounting of the cutting blade is required, remove the spindle bolt and outside blade flange. Align cutting blade with inside flange arbor and reassemble spindle and outside blade flange.

7.Cutting Head Handle — Grab hold of this handle to control the movement of the cutting head.

8.Power ON/OFF Switch — To turn on the saw place in the ON position. Place in the OFF position to shut down the saw.

9.Water Pump Power Receptacle — Plug the water pump power cord into this AC receptacle.

10.Blade Guard — Protects the user from the cutting blade. NEVER operate the saw with the blade guard removed.

11.Blade Guard Adjustment Knob — Turn knob clockwise to loosen and remove blade guard. Turn counterclockwise to tighten.

12.Blade Guard Brushes — Prevents foreign matter and debris from accumulating on the saw blade. Replace brushes immediately when they become worn or damaged.

13.CuttingTable — Place material to be cut on this rubber padded table. For ease of cutting, this table has been placed on rails so that it can easily slide back and forth.

14.Ruler Backstop — When cutting, place material against backstop. Use measurement rail (ruler) to determine where material is to be cut.

15.Stopper — Place stopper in water tray when filling with water.

16.Carrying Handles — There are two carrying handles at each end of the saw. Grip these handles when transporting of the the saw is required.

17.Cutting Head Adjustment Knob — Turn knob clockwise to loosen and position cutting head to desired height. Turn counterclockwise to tighten.

18.Water Tray — When wet cutting is required, fill with clean fresh water. Make sure submersible pump is totally immersed in water.

19.Electric Water Pump — The electric water pump for this saw requires 115 VAC. Plug power cord of electric water pump into AC receptacle located on conduit box. NEVER run pump dry. Pump must be immersed in water.

20.Water Lines — Replace the clear vinyl tubing water lines when they become brittle, worn or clogged.Water kits are available through your Multiquip dealer.

21.MaintenanceWrench — Use this multi-purpose wrench when performing maintenance or repairs on the saw.

22.Rear DripTray — Rear drip tray increases the surface area for collecting water and slurry to prevent spillage.

23.MasterGuide Template Base — Mounts to ruler backstop to ensures precision while making cuts.

24.Water LInk Hose — Recycles water from the bearing housing back into the water tray.

25.Bearing Housing — Houses permanently lubricated ball bearings to allow motor shaft to rotate smoothly.

TP24X TILE SAW • operation and parts manual — rev. #2 (04/12/12) — page 15

Image 15
Contents Model TP24X Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsTP24X Tile Saw Table of ContentsChoose from three easy options SaFeTy meSSageS Safety InformationGeneraL SaFeTy BLade SaFeTy SaW SaFeTyTranSporTIng SaFeTy ELeCTrIC moTor SaFeTyPower Cord/Cable Safety LIFTIng SaFeTy3200 SpecificationsDimensions DimensionsDry Cutting Applications Accessories/Replacement PartsFeatures General informationTP24X Tile SAW operation and parts manual rev. #2 04/12/12 Saw Components Saw componentsStopper Place stopper in water tray when filling with water Saw set-up Support Stand Assembly OptionalElectric motor components/set-up Electric Motor ComponentsWater Pump Assembly Rear drip tray installationSet-up Blades Blade ComponentsCutting Depth See for proper blade use guidelines Blade InstallationNever grab or touch a live Power cord with wet hands, Connecting the PowerSawing Guides Using the Cutting Table Place the power ON/OFF switch in the OFF position downPerforming Diagonal Cuts Using the Drip GuardSawing guides Performing Straight CutsOperation Start-up ProcedureWait for the cutting blade to stop rotating Shut down ProcedureInspect the cutting table periodically. Replace worn parts Basic MaintenanceAfter not using the machine for a prolonged period of time Maintenance intervalsAfter wet cleaning and before using the machine again Before not using the machine for a prolonged period of timeWater pump maintenance Belt replacementTake off the old belt and replace with new belt Bearing Housing Installation Bearing housing removalForth. If the table binds against the rail at any Realignment MethodIntially, but shifts apart as the table travels along Rail, proceed to MethodShim may be required Further adjustment-repeat stepMethod Table from the guide rails. See FigureTransporting the saw Leveling AdjustmentElectric Motor Wiring Diagram Wiring diagram electric motorBlade Troubleshooting Troubleshooting bladeSaw Troubleshooting Troubleshooting SawExplanation of Code in Remarks Column Tp24x tile saw with electric motor 1 to 3 units Suggested Spare PartsMain SAW Assy Part Name Cutting Head Assy Part Name QTY Remarks Cutting table assy Cutting table assy Blade guard assy Remarks Bearing housing assy Bearing housing assy Switch Box assy Includes items w/@ Tools and accessories Optional TPS100034TP100102 FreIgHT poLICy Terms and Conditions of Sale PartsTP24X Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help