Multiquip TP24X manual SaW SaFeTy, BLade SaFeTy

Page 8

Safety Information

SaW SaFeTy

danger

„never operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fi re could result causing severe bodily harm or even death.

WarnIng

„ Accidental starting can cause severe injury or death. aLWayS place the ON/OFF switch in the OFF position.

„ Keep hands away from moving parts at all times.

„never disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

CauTIon

„aLWayS ensure saw is securely placed on appropriate blocks or jackstands when maintenance requires elevation of the saw.

„If the machine malfunctions, stop the saw immediately and secure it. Fix the problem as soon as possible.

NOTICE

„aLWayS keep the machine in proper running condition.

„Fix damage to machine and replace any broken parts immediately.

„Make sure there is no buildup of grease, oil or debris on the machine.

„aLWayS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

BLade SaFeTy

WarnIng

„Rotating blade can cut and crush. aLWayS keep hands and feet clear while operating

the saw.

CauTIon

„never operate the saw without blade guards and covers in place. Exposure of the diamond blade must not exceed 180 degrees.

„Verify the motor start switch is set to the OFF position before installing a blade.

„aLWayS inspect blade before each use. The blade should exhibit no cracks, dings, or fl aws in the steel centered core and/or rim. Center (arbor) hole must be undamaged and true.

NOTICE

„Use proper blades and follow blade manufacturer’s recommendations. Match the blade RPM (blade shaft RPM) to the recommended blade surface feet per minute (SFPM).

„Ensure the blade-mounting bolt is tightened adequately

„aLWayS examine blade flanges for damage and excessive wear.

„Ensure the blade is marked with an operating speed greater than the spindle speed of the saw.

„Only cut the material that is specifi ed for the diamond blade. Read the specifi cation of the diamond blade to ensure the proper tool has been matched to the material being cut.

„If wet cutting, ensure a WeT CuTTIng blade is being used and that the water supply system to the blade is properly functioning and being used.

„do noT drop the diamond blade on ground or surface.

„Ensure that the blade is mounted for proper operating direction.

„Adhere to the blade manufacturer’s recommendations on handling, storage and safe usage of blades.

page 8 — TP24X TILE SAW • operation and parts manual — rev. #2 (04/12/12)

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model TP24X Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents TP24X Tile SawChoose from three easy options Safety Information SaFeTy meSSageSGeneraL SaFeTy SaW SaFeTy BLade SaFeTyELeCTrIC moTor SaFeTy Power Cord/Cable SafetyLIFTIng SaFeTy TranSporTIng SaFeTySpecifications 3200Dimensions DimensionsAccessories/Replacement Parts FeaturesGeneral information Dry Cutting ApplicationsTP24X Tile SAW operation and parts manual rev. #2 04/12/12 Saw components Saw ComponentsStopper Place stopper in water tray when filling with water Support Stand Assembly Optional Electric motor components/set-upElectric Motor Components Saw set-upSet-up Water Pump AssemblyRear drip tray installation Cutting Depth BladesBlade Components Blade Installation See for proper blade use guidelinesConnecting the Power Sawing Guides Using the Cutting TablePlace the power ON/OFF switch in the OFF position down Never grab or touch a live Power cord with wet hands,Using the Drip Guard Sawing guidesPerforming Straight Cuts Performing Diagonal CutsStart-up Procedure OperationShut down Procedure Wait for the cutting blade to stop rotatingBasic Maintenance Inspect the cutting table periodically. Replace worn partsMaintenance intervals After wet cleaning and before using the machine againBefore not using the machine for a prolonged period of time After not using the machine for a prolonged period of timeTake off the old belt and replace with new belt Water pump maintenanceBelt replacement Bearing housing removal Bearing Housing InstallationRealignment Method Intially, but shifts apart as the table travels alongRail, proceed to Method Forth. If the table binds against the rail at anyFurther adjustment-repeat step MethodTable from the guide rails. See Figure Shim may be requiredLeveling Adjustment Transporting the sawWiring diagram electric motor Electric Motor Wiring DiagramTroubleshooting blade Blade TroubleshootingTroubleshooting Saw Saw TroubleshootingExplanation of Code in Remarks Column Suggested Spare Parts Tp24x tile saw with electric motor 1 to 3 unitsMain SAW Assy Part Name Cutting Head Assy Part Name QTY Remarks Cutting table assy Cutting table assy Blade guard assy Remarks Bearing housing assy Bearing housing assy Switch Box assy Includes items w/@ Tools and accessories TP100102 OptionalTPS100034 Terms and Conditions of Sale Parts FreIgHT poLICyTP24X Tile SAW operation and parts manual rev. #2 04/12/12 HERE’S HOW to GET Help
Top Page Image Contents