Multiquip STX55J6 operation manual General Safety, Maintenance Safety

Page 9

STX-SERIES RULES FOR SAFE OPERATION

CAUTION

Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only and should not be regarded as a toy.

The following safety guidelines should always be used when operating the STX-SERIES Ride-on Power Trowel:

GENERAL SAFETY

DO NOT operate or service this equipment before reading this entire manual.

This equipment should not be operated by persons under 18 years of age.

DO NOT operate this equipment unless all guards and safety devices are attached and in place.

ALWAYS use proper heavy lifting techniques when moving equipment. This ride-on trowel is very heavy. It should be lifted only with a lifting device (i.e. crane, forklift, etc.) with a lifting capacity of at least one ton.

ALWAYS check to make sure that the operating area is clear before starting the engine.

ALWAYS test the safety safety stop switch before operating the equipment.

NEVER place your feet inside the guard rings while starting or operating this equipment.

NEVER operate this equipment without proper protective clothing, shatterproof glasses, steel-toed boots and other protective devices required by the job. Avoid wearing jewelry or loose fitting clothing that may snag on the controls or moving parts, this can cause a serious injury.

ALWAYS keep clear of rotating or moving parts while operating this equipment.

NEVER leave the machine unattended while running.

ALWAYS refuel in a well-ventilated area, away from sparks and open flames.

ALWAYS use extreme caution when working with flammable liquids. When refueling, stop the engine and allow it to cool. DO NOT smoke around or near the machine. Fire or explosion could result from flames or sparks, or if fuel is spilled on a hot engine.

Moving Parts – Shut down the engine before performing service or maintenance functions. Contact with moving parts can cause serious injury.

HighTemperatures – Allow the machine and engine to cool before adding fuel or performing service and maintenance functions. Contact with hot components can cause serious burns.

Maintenance Safety

Disconnect the battery and spark plug wires before attempting any type of service.

Securely support any machine components that must be raised.

NEVER lubricate components or attempt service on a running machine.

ALWAYS allow the machine a proper amount of time to cool before servicing.

Keep the machinery in proper running condition.

Make sure that there is no buildup of concrete, grease, oil or debris on the machine.

Fix damage to the machine immediately and always replace broken parts.

Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.

DO NOT use food or plastic containers to dispose of hazardous waste.

DO NOT pour waste, oil or fuel directly onto the ground, down a drain or into any water source.

STX-SERIESRIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (07/16/04) — PAGE 9

Image 9
Contents STX Series RIDE-ON Power Trowel Page Heres HOW to GET Help STX-SERIES Table of Contents Training Checklist STX-SERIES Training ChecklistDaily PRE-OPERATION Checklist STX-SERIES Daily PRE-OPERATION ChecklistDo not follow directions STX-SERIES Safety Message Alert SymbolsEmergencies STX-SERIES Safety Message Alert SymbolsMaintenance Safety General SafetyOperation and Safety Decals STX-SERIES Operation and Safety DecalsThis value includes the seat height STX-SERIES SpecificationsGeneral Information STX-SERIES General InformationToolbox Compartment Storage for tools STX-SERIES Controls and Components FrontSTX-SERIES Controls and Components Rear STX-SERIES Controls and ComponentsPRE-INSPECTION STX-SERIES PRE-INSPECTIONEngine Oil FuelSTX-SERIES Initial START-UP Insert the ignition key into the ignition switch FigureInitial START-UP Starting the EngineSTX-SERIES Initial START-UP Oil and Charge Indicator LightsSTX-SERIES Operation OperationSteering Push both the left and right joysticks forward Figure STX-SERIES OperationEngine Shut-Down Blade Pitch ControlFailure to allow the engine to idle Left Pitch all the way DownSTX-SERIES Maintenance MaintenanceMaintenance Procedures Matching Blade Pitch for Both Sets of Blades STX-SERIES MaintenanceChanging a Blade Blade Pitch Adjustment BoltPressure Gauge Hydraulic Pump Checking Hydraulic PressureChecking Steering Pressure Steering Pressure AdjustmentPitch Pressure Check Pitch Pressure AdjustmentTroubleshooting STX-SERIES TroubleshootingLights optional not working Lights? STX-SERIES TroubleshootingPage Multiquip INC
Related manuals
Manual 64 pages 22.72 Kb