Tensioning Blade
6 egdeZgan iZch^dcZY WaVYZ ^h ZhhZci^Va [dg bV`" ^c\VXXjgViZXjihVcY^hVegZgZfj^h^iZ[dgbV`^c\ bVcnWVcYhVlVY_jhibZcih#I]ZWaVYZiZch^dc^h VY_jhiZYWngdiVi^c\i]ZWaVYZiZch^dcaZkZg#
To tension the bandsaw blade:
1. BV`ZhjgZndj]VkZeZg[dgbZYi]ZTest Run
^chigjXi^dchdci]ZegZk^djheV\ZVcYndjVgZ
XZgiV^ci]Vii]ZWaVYZ^higVX`^c\egdeZgan#
2. L^i] i]Z WaVYZ iZch^dc aZkZg ^c i]Z Ydlc Zc\V\ZY edh^i^dc! VY_jhi i]Z WaVYZ iZch^dc jci^a i]Z bVg` dc i]Z WaVYZ iZch^dc hXVaZ bViX]Zh i]Z h^oZ d[ WaVYZ ^chiVaaZY dc i]Z WVcYhVl#
Note:Because each blade is different and all blades stretch, this scale can only be consid- ered as a general guide.
3. Ijgci]ZWVcYhVlON#
4. GZaZVhZi]ZiZch^dcdcZfjVgiZgd[VijgcViV i^bZ#L]Zci]ZWVcYhVlWaVYZhiVgihid[aji" iZg!hideYZXgZVh^c\i]ZiZch^dc#
5. Cdl! hadlan ^cXgZVhZ i]Z iZch^dc jci^a i]Z WaVYZhideh[ajiiZg^c\!i]Zci^\]iZci]ZiZch^dc dcZbdgZfjVgiZgd[Vijgc#
6. Ijgci]ZWVcYhVlD;;VcYgZVYi]ZiZch^dc \Vj\Z#JhZi]ZgZVY^c\VhV\j^YZl]ZciZc" h^dc^c\i]ViWaVYZ^ci]Z[jijgZ#
Note: Do not rely on this measurement for long periods of time because the blade will stretch with use.
NOTICE
To reduce blade stretching, remove the ten- sion from the blade when not in use.
NOTICE
After blade tension and tracking are set cor- rectly, properly adjust the upper/lower sup- port bearings and
"'%"
Adjusting Support
Bearings
I]Z hjeedgi WZVg^c\h VgZ edh^i^dcZY WZ]^cY i]Z WaVYZ id hjeedgi ^i Yjg^c\ Xjii^c\ deZgVi^dch# EgdeZg VY_jhibZci d[ i]Z hjeedgi WZVg^c\h ^h Vc ^bedgiVci eVgi d[ bV`^c\ VXXjgViZ Xjih VcY Vahd`ZZehi]ZWaVYZiZZi][gdb]^ii^c\i]ZWaVYZ \j^YZhYjg^c\Xjih#
To adjust the support bearings:
1. BV`ZhjgZi]Vii]ZWaVYZ^higVX`^c\egdeZgan | ||
VcYi]Vi^i^hXdggZXianiZch^dcZY# | ||
2. 9>H8DCC:8I76C9H6L;GDBEDL:G | ||
3. ;Vb^a^Vg^oZndjghZa[l^i]i]ZhjeedgiWZVg^c\ | ||
Xdcigdahh]dlc^cFigure 20# | ||
| AdX`7dai | |
Hjeedgi | I]jbWhXgZl | |
7ZVg^c\ | ||
| ||
Figure 20.HjeedgiWZVg^c\Xdcigdah# | ||
4.GZbdkZi]ZWaVYZ\jVgY#
5. AddhZci]ZadX`Wdaih]dlc^cFigure 20#