Grizzly Model G1023zx3 instruction manual Start Up Recommended, Starting the machine

Page 29

Start Up				Recommended
				Adjustments

Loose hair and clothing could get caught in machinery causing seri- ous personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery.

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses during assembly.

Before starting the machine:

1.Read this manual and make sure you take all safety precautions before operating this machine.

2.Make sure the blade guard and splitter have been correctly installed and are adjusted properly as shown on Pages 23-25.

3.Make sure that any tools or foreign objects have been removed from the machine.

4.Review Section 3: Circuit Requirements beginning on Page 8 and make sure all wiring is correct.

5.Keep your finger on the STOP button during the entire test run of the machine.

Starting the machine:

Turn the machine on and make sure your hand is on the STOP button in case you need to shut the machine off immediately. The machine should run smoothly with little or no vibration.

For your convenience, the adjustments listed below have been performed at the factory and no further setup is required to operate your machine.

However, because of the many variables involved with shipping, we recommend that you at least check the following adjustments to ensure the best possible results from your new machine.

All of these adjustments are covered in step-by- step detail in Section 8: Service Adjustments.

Recommended adjustment checklist:

¥45û & 90û Stops (Page 39)

¥Blade Parallelism (Page 40)

¥Blade Alignment (Page 42)




G1023Z Series Heavy-Duty 10'' Table Saw			-27-

Image 29

Contents Model G1023Z, ZX & ZX3 HEAVY-DUTY Table SAWPage Table of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesFeatherboards Zero Clearance Table InsertsPush Paddles Commentary IntroductionG1023Z Circuit RequirementsG1023ZX G1023ZX3 Grounding Extension Cord Terms & Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPG1023Z Series component layout Hardware Recognition Chart Site Considerations Clean UpFloor Load Working ClearanceBeginning Assembly Extension Wings To mount the switch SwitchDisconnect the machine from the power source Fence & RailsDust Hood Motor Cover To mount the dust hood and cleanout doorGuard Bracket Motor BraceTable Insert HandwheelBlade Guard/Splitter Saw Blade Front Support Blade Adjustment Bolt Miter Gauge To adjust the miter gaugeStarting the machine Recommended adjustment checklistStart Up Recommended Blade Selection OperationsPage Cross-cut operation G1023Z Series Heavy-Duty 10 Table Saw CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1023Z Series Heavy-Duty 10 Table Saw Rabbet CuttingRabbet cutting G1023Z Series Heavy-Duty 10 Table Saw Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table Saw General MaintenanceLubricate the areas indicated below every 12 months LubricationTableBelt Belt deflection Date Approximate Hours Of Use Maintenance Performed 45˚ & 90˚ Stops Service AdjustmentsBlade Parallelism Page Trunnion mounting bolts Blade AlignmentPage G1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Page Closure G1023Z / G1023ZX / G1023ZX3 Machine Data SheetG1023Z Series Heavy-Duty 10 Table Saw Cabinet Complete Miter Gauge Symptom Possible Cause Corrective Action Troubleshooting GuideG1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog