Grizzly Model G1023zx3 instruction manual Grounding Extension Cord

Page 13

Grounding

 

Extension Cord

 

 

 

 

 

 

Electrocution or a fire can result if the band- saw is not grounded cor- rectly. Make sure all electrical circuits are grounded. Do not use the machine if it is not grounded.

NOTICE

The wire on the power cord with green or green and yellow striped insulation is the grounding conductor.

In the event of an electrical short, grounding pro- vides electric current a path of least resistance to reduce the risk of electrical shock to the operator. Ground the power cord and this machine in accor- dance with all local codes and ordinances.

Operating this machine when it is not properly grounded can result in electric shock or electro- cution.

Should it be necessary to use an extension make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in Section 1: Safety Instructions to determine the minimum gauge for the extension cord. The extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords when they become worn or damaged.

No single list of electrical guidelines can be comprehensive for all shop environ- ments. Operating this machinery may require additional electrical upgrades spe- cific to your machine and shop environ- ment. It is your responsibility to make sure your electrical systems comply with all local electrical codes and ordinances.

 

 

 

 

 

 

 

 

 

 

 

 

G1023Z Series Heavy-Duty 10'' Table Saw

-11-

Image 13
Contents Model G1023Z, ZX & ZX3 HEAVY-DUTY Table SAWPage Table of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesPush Paddles Zero Clearance Table InsertsFeatherboards Commentary IntroductionG1023Z Circuit RequirementsG1023ZX G1023ZX3 Grounding Extension Cord Terms & Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPG1023Z Series component layout Hardware Recognition Chart Site Considerations Clean UpFloor Load Working ClearanceBeginning Assembly Extension Wings To mount the switch SwitchDisconnect the machine from the power source Fence & RailsDust Hood Motor Cover To mount the dust hood and cleanout doorGuard Bracket Motor BraceTable Insert HandwheelBlade Guard/Splitter Saw BladeFront Support Blade Adjustment Bolt Miter Gauge To adjust the miter gaugeStart Up Recommended Recommended adjustment checklistStarting the machine Blade Selection OperationsPage Cross-cut operation G1023Z Series Heavy-Duty 10 Table Saw CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1023Z Series Heavy-Duty 10 Table Saw Rabbet CuttingRabbet cutting G1023Z Series Heavy-Duty 10 Table Saw Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table Saw General MaintenanceBelt LubricationTableLubricate the areas indicated below every 12 months Belt deflection Date Approximate Hours Of Use Maintenance Performed 45˚ & 90˚ Stops Service AdjustmentsBlade Parallelism Page Trunnion mounting bolts Blade AlignmentPage G1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Page Closure G1023Z / G1023ZX / G1023ZX3 Machine Data SheetG1023Z Series Heavy-Duty 10 Table Saw Cabinet Complete Miter Gauge Symptom Possible Cause Corrective Action Troubleshooting GuideG1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog