Grizzly Model G1023zx3 instruction manual Blade Adjustment Bolt

Page 27

6.Recheck the splitter alignment to the blade and to the table top. Adjust as necessary and tighten all the bolts before use. If the blade guard is properly aligned, please skip ahead to Step 13; otherwise, continue with the next step.

7.If the splitter is positioned to the left of the blade, alignment cannot be achieved by washer placement. Adjustment of the front support bracket is required. See Figure 21 for adjustment details. Loosen the 2 adjust- ment screws and move left or right.

8.If this adjustment does not allow enough movement of the splitter, remove the table and wings, and set them to one side. Be sure to note the position of the table shims. Replace them to their original position before re-attaching the table.

The table and wings represent a very heavy load. DO NOT over- exert yourself while lift- ing or moving the table and wings – get assis- tance.

The arbor bracket and motor pulley now need to be adjusted:

9.Loosen the adjustment bolt shown in Figure 23, and slowly slide the arbor bracket towards the end of the shaft. Only move the arbor bracket a distance equal to the amount of misalignment between the blade and the splitter, or a little more. You can always adjust the splitter back to the left with wash- ers.

10.Tighten the adjustment bolt securely.

G1023Z Series Heavy-Duty 10'' Table Saw

Blade Adjustment Bolt

Arbor Bracket

Figure 23. Arbor bracket adjustment locations.

11.Moving the arbor bracket moves the V-belts and pulleys out of alignment, so adjustment of the motor pulley is required. Simply loosen the setscrew in the middle groove of the pul- ley, and slowly slide the pulley toward the end of the motor shaft. Once the V-belts are back in alignment, tighten the setscrew securely.

12.Recheck the guard alignment to the blade and to the table top. Adjust as necessary and tighten down all the bolts before use. If the blade guard is properly aligned, re-attach the table, making sure there is adequate blade clearance through all blade adjustments.

13.Adjust the blade to 45¡. Raise and lower it through the full range. Re-adjust the blade to 90¡, then raise and lower it through the full range. There should be no contact between the blade, the base, the table insert, or any other part of the saw. If there is contact, repeat Steps 8-12.

-25-

Image 27
Contents Model G1023Z, ZX & ZX3 HEAVY-DUTY Table SAWPage Table of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesZero Clearance Table Inserts Push PaddlesFeatherboards Commentary IntroductionG1023Z Circuit RequirementsG1023ZX G1023ZX3 Grounding Extension Cord Terms & Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPG1023Z Series component layout Hardware Recognition Chart Working Clearance Clean UpSite Considerations Floor LoadBeginning Assembly Extension Wings Fence & Rails SwitchTo mount the switch Disconnect the machine from the power sourceDust Hood Motor Cover To mount the dust hood and cleanout doorGuard Bracket Motor BraceTable Insert HandwheelBlade Guard/Splitter Saw BladeFront Support Blade Adjustment Bolt Miter Gauge To adjust the miter gaugeRecommended adjustment checklist Start Up RecommendedStarting the machine Blade Selection OperationsPage Cross-cut operation G1023Z Series Heavy-Duty 10 Table Saw CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1023Z Series Heavy-Duty 10 Table Saw Rabbet CuttingRabbet cutting G1023Z Series Heavy-Duty 10 Table Saw Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table Saw General MaintenanceLubricationTable BeltLubricate the areas indicated below every 12 months Belt deflection Date Approximate Hours Of Use Maintenance Performed 45˚ & 90˚ Stops Service AdjustmentsBlade Parallelism Page Trunnion mounting bolts Blade AlignmentPage G1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Page Closure G1023Z / G1023ZX / G1023ZX3 Machine Data SheetG1023Z Series Heavy-Duty 10 Table Saw Cabinet Complete Miter Gauge Symptom Possible Cause Corrective Action Troubleshooting GuideG1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog