Grizzly Model G1023zx3 instruction manual Saw Blade, Blade Guard/Splitter

Page 25

Saw Blade

To install a saw blade:

1.Disconnect the machine from the power source!

2.The arbor nut has left-hand threads. Loosen the arbor nut clockwise and remove the outside flange from the arbor. Remove and discard the 3Ú4'' diameter spacer on the arbor shaft.

Use caution and remain alert when working with the saw blade. Failure to follow this warning could result in serious personal injury or death.

3. Install the saw blade onto the arbor. Ensure that the blade teeth point toward you as you stand at the front of the saw.

4. Slide on the flange and thread the arbor nut back on.

5. Use the arbor wrench provided with the saw to tighten the arbor nut. Wedge a block of wood in the teeth of the blade to keep it from turning when tightening the nut as shown in

Figure 17.

!

Figure 17. Changing saw blade.

G1023Z Series Heavy-Duty 10'' Table Saw

Blade Guard/Splitter

To install a blade guard/splitter:

1.Disconnect the machine from the power source!

2.Slip the blade guard/splitter over the mount- ing bolts as shown in Figure 18. The wash- ers should be between the bolt head and the slots. Tighten the bolts to secure the blade guard/splitter.

Blade Guard

Mounting Bolt

Anti-kickback Pawl

Figure 18. Blade guard and splitter in place.

3.Set a machinistÕs square against the face of the blade splitter. Slightly rotate the rear bracket to adjust the face of the blade splitter perpendicular to the table top as shown in

Figure 19.

!

Figure 19. Blade splitter square to table.

-23-

Image 25

Contents Model G1023Z, ZX & ZX3 HEAVY-DUTY Table SAWPage Table of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesPush Paddles Zero Clearance Table InsertsFeatherboards Commentary IntroductionG1023Z Circuit RequirementsG1023ZX G1023ZX3 Grounding Extension Cord Terms & Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPG1023Z Series component layout Hardware Recognition Chart Site Considerations Clean UpFloor Load Working ClearanceBeginning Assembly Extension Wings To mount the switch SwitchDisconnect the machine from the power source Fence & RailsDust Hood Motor Cover To mount the dust hood and cleanout doorGuard Bracket Motor BraceTable Insert HandwheelBlade Guard/Splitter Saw BladeFront Support Blade Adjustment Bolt Miter Gauge To adjust the miter gaugeStart Up Recommended Recommended adjustment checklistStarting the machine Blade Selection OperationsPage Cross-cut operation G1023Z Series Heavy-Duty 10 Table Saw CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1023Z Series Heavy-Duty 10 Table Saw Rabbet CuttingRabbet cutting G1023Z Series Heavy-Duty 10 Table Saw Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table Saw General MaintenanceBelt LubricationTableLubricate the areas indicated below every 12 months Belt deflection Date Approximate Hours Of Use Maintenance Performed 45˚ & 90˚ Stops Service AdjustmentsBlade Parallelism Page Trunnion mounting bolts Blade AlignmentPage G1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Page Closure G1023Z / G1023ZX / G1023ZX3 Machine Data SheetG1023Z Series Heavy-Duty 10 Table Saw Cabinet Complete Miter Gauge Symptom Possible Cause Corrective Action Troubleshooting GuideG1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog