Grizzly G1073/G1073Z instruction manual Unpacking Piece Inventory, Hardware Qty

Page 10

Unpacking

Piece Inventory

 

 

 

 

 

 

The Model G1073 Bandsaw is shipped from the manufacturer in a carefully packed carton, and the Model G1073Z is shipped in two cartons. If you discover the machine is damaged after you have signed for delivery, please call Customer Service immediately for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise filing a freight claim can be difficult.

When you are completely satisfied with the con- dition of your shipment, you should inventory its parts.

The Model G1073/G1073Z is a heavy machine (456 lbs. ship- ping weight). DO NOT over- exert yourself while unpack- ing or moving your machine – get assistance.

If moving this machine up or down stairs, the machine must be disman- tled and moved in smaller pieces. Make sure the stairs are capable of sup- porting the combined weight of the machine parts and the people mov- ing them.

Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury.

After all the parts have been removed from the carton, you should have:

•Bandsaw Unit with Blade

•Motor

•Stand Parts (1073)

¥Cabinet Stand (1073Z)

• Table Support Bracket

• Miter Gauge

• Table

• Mounting Bracket

• Fence

• V-Belt

• Pulley Guard

• Dust Port

Hardware

Qty

Carriage Bolts 5Ú16"-18 x 5Ú8"

24

(does not apply for G1073Z)

 

Hex Bolts 1Ú4"-20 x 3Ú4"

2

Hex Bolts 5Ú16"-18 x 1"

4

Carriage Bolts 5Ú16"-18 x 1"

4

(does not apply for G1073Z)

 

Hex Bolts 3Ú8"-16 x 1"

2

Hex Bolts 3Ú8"-16 x 2"

4

Hex Nuts 1Ú4"-20

2

Hex Nuts 5Ú16"-18

32

(4 for G1073Z)

 

Hex Nuts 3Ú8"-16

6

(4 for G1073Z)

 

Flat Washers 5Ú16"

32

(4 for G1073Z)

 

Anti Vibration Pads

4

Flat Washers 3Ú8"

12

(8 for G1073Z)

 

Cap Screws 1Ú4"-20 x 11Ú4"

4

Fence Rail Spacers

4

Flat Washers 1Ú4"

4

In the event that any non-proprietary parts are missing (e.g. nuts or washers), we would be glad to replace them, or for the sake of expediency, replacements can be obtained at your local hard- ware store.

-8-

G1073/G1073Z 16" Bandsaw

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Bandsaw Model G1073/G1073ZPage Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For Bandsaws 220V Operation 110V Operation Circuit RequirementsExtension Cords Grounding General Information Unpacking Piece Inventory Hardware QtyClean up Site Considerations Stand G1073 AssemblyTo assemble the stand Bandsaw To Stand Wiring The Motor Belt To install the V-beltMotor Mount Bolts Working Table To mount the table and trunnion supportTo mount the rails FenceThere are two ways to remove the fence Guard Dust Port To mount the dust portBlade Tension AdjustmentsTo adjust the tension Blade TrackingBlade Guides Eccentric blade supportTable Stop Guide BlocksTo position the blade line parallel to the miter slot Table ParallelismTable Tilt To tilt the tableBlade Changes Guide Post To adjust the guide post bracketTo check guide post alignment To adjust the rear clamping pressure Fence AdjustmentTo shift the blade Blade Lead To skew your fenceTo verify if the the upper and lower wheels are coplanar Wheel AlignmentShimming a wheel Adjusting Parallelism Test Run OperationsBlade Selections Resawing Table Adjustment sectionCutting Curves To resaw lumberBelts MaintenanceV-belt is accessed via the bottom cover MiscellaneousClosure G1073/G1073Z 16 Bandsaw Model G1073/G1073Z 16 Bandsaw 104 111A 129A 128 108-1 127 81C 126 174 190 108165 130A 139 95A 117Ł 13A 138 137A 136 135 G1073/G1073Z 16 Bandsaw 184 Model Model 1073Z Main Body Casting PSB07 Troubleshooting Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA
Top Page Image Contents