Grizzly instruction manual Model G1073/G1073Z 16 Bandsaw

Page 34

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 ¥ To Order Call: (800) 523-4777 ¥ Fax #: (800) 438-5901

MODEL G1073/G1073Z 16" BANDSAW

Design Type:	2 Wheel Floor Model, 3 Speed
(G1073 Open Stand, G1073Z Cabinet Stand)
Overall Dimensions:
Table	17" x 17" x 11Ú2" Thick
Stand	16" H x 24" W x 21" L
Overall Height	72"
Height from Floor to Table	40"
Width of Unit	35"
Depth of Unit	20"
Shipping Weight	Approx. 456 lbs.
Crate Size	16" H x 26" W x 60" L
Cutting Capacity:
Left of Blade	16 1Ú4"
Height	7 3Ú4"
Construction:
Table	Precision Ground Cast Iron
Wheels	Fully Balanced Cast Iron with Rubber Tire
Rip Fence	Double Lock, Adjustable, Extruded Aluminum
Wheel Covers	Preformed Steel
Guides	Steel Blocks with Ball Bearing Guides
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	2 H.P.
Phase/Cycle	Single-Phase/60 Hz
Voltage	110V/220V-prewired 220V
Amps	24A @ 110V/12A @ 220V
R.P.M. ....................................................................................................................................1725
Bearings	Shielded and Permanently Lubricated Ball
Switch	Paddle w/Safety Lock Key
Blade:
Sizes Available	1Ú8" - 1"
Standard Blade Length	113"
Blade Speeds	2275, 2720, 3265 F.P.M.
Specifications, while deemed accurate, are not guaranteed.
-32-	G1073/G1073Z 16" Bandsaw

Image 34

Contents Bandsaw Model G1073/G1073ZPage Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For Bandsaws 220V Operation 110V Operation Circuit RequirementsExtension Cords Grounding General Information Unpacking Piece Inventory Hardware QtyClean up Site Considerations Stand G1073 AssemblyTo assemble the stand Bandsaw To Stand Wiring The Motor Belt To install the V-beltMotor Mount Bolts Working Table To mount the table and trunnion supportTo mount the rails FenceThere are two ways to remove the fence Guard Dust Port To mount the dust portBlade Tension AdjustmentsTo adjust the tension Blade TrackingBlade Guides Eccentric blade supportTable Stop Guide BlocksTo position the blade line parallel to the miter slot Table ParallelismTable Tilt To tilt the tableBlade Changes Guide Post To adjust the guide post bracketTo check guide post alignment To adjust the rear clamping pressure Fence AdjustmentTo shift the blade Blade Lead To skew your fenceTo verify if the the upper and lower wheels are coplanar Wheel AlignmentShimming a wheel Adjusting Parallelism Test Run OperationsBlade Selections Resawing Table Adjustment sectionCutting Curves To resaw lumberBelts MaintenanceV-belt is accessed via the bottom cover MiscellaneousClosure G1073/G1073Z 16 Bandsaw Model G1073/G1073Z 16 Bandsaw 104 111A 129A 128 108-1 127 81C 126 174 190 108165 130A 139 95A 117Ł 13A 138 137A 136 135 G1073/G1073Z 16 Bandsaw 184 Model Model 1073Z Main Body Casting PSB07 Troubleshooting Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA