Grizzly G1073/G1073Z instruction manual Safety Instructions For Power Tools

Page 4

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

 

 

 

 

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

WILL result in death or serious injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COULD result in death or serious injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

 

 

 

 

against unsafe practices.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTICE

 

This symbol is used to alert the user to useful information about

 

 

proper operation of the equipment.

 

 

 

 

 

 

 

 

 

Safety Instructions For Power Tools

1.KEEP GUARDS IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.DO NOT USE IN DANGEROUS ENVI- RONMENT. Do not use power tools in damp or wet locations, or where any flam- mable or noxious fumes may exist. Keep work area well lighted.

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.

6.MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.

7.DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

-2-

G1073/G1073Z 16" Bandsaw

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Bandsaw Model G1073/G1073ZPage Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For Bandsaws 220V Operation 110V Operation Circuit RequirementsExtension Cords Grounding General Information Unpacking Piece Inventory Hardware QtyClean up Site Considerations Stand G1073 AssemblyTo assemble the stand Bandsaw To Stand Wiring The Motor Belt To install the V-beltMotor Mount Bolts Working Table To mount the table and trunnion supportTo mount the rails FenceThere are two ways to remove the fence Guard Dust Port To mount the dust portAdjustments To adjust the tensionBlade Tension Blade TrackingBlade Guides Eccentric blade supportTable Stop Guide BlocksTable Parallelism Table TiltTo position the blade line parallel to the miter slot To tilt the tableBlade Changes Guide Post To adjust the guide post bracketTo check guide post alignment To adjust the rear clamping pressure Fence AdjustmentTo shift the blade Blade Lead To skew your fenceTo verify if the the upper and lower wheels are coplanar Wheel AlignmentShimming a wheel Adjusting Parallelism Test Run OperationsBlade Selections Table Adjustment section Cutting CurvesResawing To resaw lumberMaintenance V-belt is accessed via the bottom coverBelts MiscellaneousClosure G1073/G1073Z 16 Bandsaw Model G1073/G1073Z 16 Bandsaw 104 111A 129A 128 108-1 127 81C 126 174 190 108165 130A 139 95A 117Ł 13A 138 137A 136 135 G1073/G1073Z 16 Bandsaw 184 Model Model 1073Z Main Body Casting PSB07 Troubleshooting Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA
Top Page Image Contents