Grizzly G1022PRO instruction manual Beginning Assembly, Stand Assembly

Page 19

SECTION 4: ASSEMBLY

Beginning Assembly

!Disconnect power to the machine when perform- ing any maintenance,

assembly or adjust- ments. Failure to do this may result in serious personal injury.

Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.

Wear safety glasses dur- ing the entire assembly process. Failure to com- ply may result in serious personal injury.

Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury.

Most of your Model G1022 Series has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps. Please follow along in the order presented here.

TOOLS REQUIRED: High quality square and straightedge, metric Allen¨ wrench set, flat screw- driver, Phillips¨ screwdriver, dead blow hammer and a 6" or 8" adjustable wrench.

G1022 Series Contractor Saws

Stand Assembly

The Model G1022 Series is supplied with a heavy-duty stand. To assemble the stand:

1.Fasten the plastic feet to all four legs using the M10-1.5 x 25 hex bolts, 10MM flat wash- ers and M10-1.5 hex nuts as shown in Figure 7.

Figure 7. Installing the rubber feet.

2.Locate the long upper and lower side braces (2 each) and bolt to the legs using the M8- 1.25 x 16 carriage bolts, 8MM flat washers and M8-1.25 hex nuts as shown in Figure 8. Do not tighten any stand bolts at this time.

Figure 8. Assembled side panel.

-17-

Image 19

Contents Table SAW Page Table Of Contents Safety Instructions For Power Tools SafetyAMP Rating Additional Safety Instructions For Table Saws Zero Clearance Table Inserts Push SticksFeatherboards Push PaddlesCommon Definitions, Terms and Phrases G1022ZF Circuit Requirements110V Operation G1022SM and G1022ZG1022ZFX and G1022PRO 220V OperationGrounding Extension Cords Commentary IntroductionG1022 Series Contractor Saws Piece Inventory UnpackingHardware Contents Bolt Hardware Recognition ChartSite Considerations Clean UpBeginning Assembly AssemblyStand Assembly All Models G1022ZF and ZFXAttaching pulley guard bracket HandwheelsMotorPage G1022ZF, G1022ZFX and G1022PRO WiringFence Rails Extension WingsBlade FenceBlade Guard Adjusting blade guardPage Table Insert Adjusting table insert height G1022 Series Contractor SawsG1022SM Fence AdjustmentsAttaching a sacrificial fence G1022 Series Contractor Saws G1022Z Fence Adjust measurement pointerAdjust measurement pointer G1022 Series Contractor Saws Blade Parallelism Table/trunnion assembly¡ blade parallelism measurement 90 Stops Next step for all models Worm GearMiter Gauge Initial Step, Model G1022ZF and ZFXPre-Run Check OperationsTest Run Ripping blade Blade SelectionVarious saw tooth cutting profiles CrosscuttingCross-cut operation RippingOptional dado blade system Dado OperationsSacrificial fence G1022 Series Contractor Saws Rabbet OperationsRabbet cutting G1022 Series Contractor Saws Tables MaintenanceGeneral LubricationG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Symptom Possible Cause Corrective Action Troubleshooting GuidePush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA