Grizzly G1022PRO instruction manual Blade Selection, Ripping blade

Page 38

4.If anything appears abnormal, immediately turn off the saw and fix the problem. If a problem exists that is beyond the scope of this manual, call our service department.

5.If the saw is behaving normally, turn it off and prepare to make a cut according to the instructions outlined in the following sec- tions.

2.Cross-cut Blade: Used for cutting across the grain. 10" cross-cut blades have between 60-80 teeth (Figure 51), alternate top bevel or steep alternate top bevel tooth profiles, small hook angle and a shallow gul- let.

Blade Selection

Choosing the correct blade for the job is essential for the safe and efficient use of your table saw. Ignoring this important step could result in dam- age to the saw and serious injury to the operator. Documented below are the most common saw blades and their uses.

1.Rip Blade: Used for cutting with the grain. Typically, 10" rip blades have between 20-40 teeth (Figure 50), flat-top ground tooth pro- file and large gullets to allow for large chip removal.

Figure 51. Crosscutting blade.

3.Combination Blade: Used for cutting with and across the grain. A compromise between a rip blade and a cross-cut blade, a 10" combination blade will typically have between 40-50 teeth (Figure 52), an alter- nate top bevel and flat or alternate top bevel and raker tooth profile. The teeth are arranged in groups of five. The gullets are small and shallow within the groups of five teeth, similar to a cross-cut blade; then large and deep between the groups, like a ripping blade.

Figure 50. Ripping blade.

-36-

Figure 52. Combination blade.

G1022 Series Contractor Saws

Image 38
Contents Table SAW Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardsCommon Definitions, Terms and Phrases G1022SM and G1022Z Circuit Requirements110V Operation G1022ZF220V Operation G1022ZFX and G1022PROGrounding Extension Cords Introduction CommentaryG1022 Series Contractor Saws Unpacking Piece InventoryHardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsStand Assembly AssemblyBeginning Assembly G1022ZF and ZFX All ModelsHandwheelsMotor Attaching pulley guard bracketPage Wiring G1022ZF, G1022ZFX and G1022PROExtension Wings Fence RailsFence BladeAdjusting blade guard Blade GuardPage Adjusting table insert height G1022 Series Contractor Saws Table InsertAdjustments G1022SM FenceAttaching a sacrificial fence G1022 Series Contractor Saws Adjust measurement pointer G1022Z FenceAdjust measurement pointer G1022 Series Contractor Saws Table/trunnion assembly Blade Parallelism¡ blade parallelism measurement 90 Stops Initial Step, Model G1022ZF and ZFX Worm GearMiter Gauge Next step for all modelsTest Run OperationsPre-Run Check Blade Selection Ripping bladeCrosscutting Various saw tooth cutting profilesRipping Cross-cut operationDado Operations Optional dado blade systemRabbet Operations Sacrificial fence G1022 Series Contractor SawsRabbet cutting G1022 Series Contractor Saws Lubrication MaintenanceGeneral TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA