Grizzly G1022PRO instruction manual Maintenance, General, Lubrication, Tables, Belt

Page 44

SECTION 7: MAINTENANCE

General

!Disconnect power to the machine when perform-

ing any maintenance or repairs. Failure to do this may result in serious personal injury.

Keep clothing rolled up and out of the way of machinery and keep hair pulled back.

Wear safety glasses dur- ing the entire mainte- nance process. Failure to comply may result in serious personal injury.

Regular periodic maintenance on your Model G1022 Series will ensure its optimum perfor- mance. Make a habit of inspecting your machine each time you use it. Check for the following con- ditions and repair or replace when necessary:

1.Loose mounting bolts.

2.Worn switch.

3.Worn or damaged cords and plugs.

4.Damaged V-belt.

5.Any other condition that could hamper the safe operation of this machine.

6.Inspect blades for damage.

7.Guard alignment and operation.

Lubrication

The sealed ball bearings in the motor and throughout the Model G1022 Series require no further lubrication during their lifetime. When they do wear out, replacements can be obtained through the Grizzly Parts Department. Lubricate the areas indicated below every 12 months.

1.Blade angling trunnions. These should be lubricated with 6 or 7 drops of light machine oil.

2.Blade height trunnion. This should also be lubricated with 6 or 7 drops of light machine oil.

3.The two (2) worm gears should be lubricat- ed with an automotive wheel bearing grease.

Tables

Tables can be kept rust-free with regular applica- tions of products like Boeshield¨ T-9. For long term storage you may want to consider products like Kleen Bore's Rust Guarditª.

V-Belt

Inspect regularly for tension and wear. Check pul- leys to ensure that they are properly aligned. See pulley/V-belt sections for proper tension and pul- ley alignment procedures.

 

 

 

 

 

 

 

 

-42-

 

 

G1022 Series Contractor Saws

 

 

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Table SAW Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardsCommon Definitions, Terms and Phrases Circuit Requirements 110V OperationG1022SM and G1022Z G1022ZF220V Operation G1022ZFX and G1022PROGrounding Extension Cords Introduction CommentaryG1022 Series Contractor Saws Unpacking Piece InventoryHardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsStand Assembly AssemblyBeginning Assembly G1022ZF and ZFX All ModelsHandwheelsMotor Attaching pulley guard bracketPage Wiring G1022ZF, G1022ZFX and G1022PROExtension Wings Fence RailsFence BladeAdjusting blade guard Blade GuardPage Adjusting table insert height G1022 Series Contractor Saws Table InsertAdjustments G1022SM FenceAttaching a sacrificial fence G1022 Series Contractor Saws Adjust measurement pointer G1022Z FenceAdjust measurement pointer G1022 Series Contractor Saws Table/trunnion assembly Blade Parallelism¡ blade parallelism measurement 90 Stops Worm Gear Miter GaugeInitial Step, Model G1022ZF and ZFX Next step for all modelsTest Run OperationsPre-Run Check Blade Selection Ripping bladeCrosscutting Various saw tooth cutting profilesRipping Cross-cut operation Dado Operations Optional dado blade systemRabbet Operations Sacrificial fence G1022 Series Contractor SawsRabbet cutting G1022 Series Contractor Saws Maintenance GeneralLubrication TablesG1022SM and Z Wiring Diagram G1022ZF, ZFX and PRO Wiring Diagram Closure Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Model G1022ZF/ZFX/PRO Table SAW G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO G1022ZF/ZFX/PRO Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick Warranty Card Warranty and Returns Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA
Top Page Image Contents