Grizzly G0555 instruction manual Blade Speed, To change the blade speed Unplug the bandsaw

Page 32

4.Make relief cuts (see definition on page 29) perpendicular to the outline of your intended shape in areas where changes in blade direction could strain the woodgrain or cause the blade kerf to bind.

5.Cut the stack of pieces as though you were cutting a single piece. Follow your layout line with the blade kerf on the waste side of your line as shown in Figure 32.

Cutting into brad nails that are used to secure the multiple pieces can cause the blade to break and may cause an injury to the operator. Be extremely careful of where you are cutting when performing this oper- ation.

Figure 32. Cutting multiple pieces at once.

-30-

Blade Speed

The Model G0555 offers blade speeds of 1500 & 3200 FPM. For general woodworking and most cutting operations, we recommend using the 3200 FPM speed. Keep in mind, the results from different speeds are related to the type of blade being usedÑwhenever determining SPEED, also choose a type of blade that is related to your operation. Use the chart below as a general guide to blade speed:

Type of Cutting Operation

Blade Speed

 

 

Most Species of Wood

3200 FPM

Super Dense Hardwood

1500 FPM

Fast/Average Feed Rate

3200 FPM

Requires Slow Feed Rate

1500 FPM

Rough Edges Tolerable

3200 FPM

 

 

Requires Smooth Edges

1500 FPM

 

 

Quick, Production Cuts

3200 FPM

Detailed, Intricate Cuts

1500 FPM

 

 

Speed changes are performed by moving the V- belt to one of the two sets of pulleys.

To change the blade speed:

1.Unplug the bandsaw!

2.Open the lower wheel cover.

3.Loosen the motor mount bolts shown in Figure 33.

Motor

Adjustment

Bolt

Motor

Hinge Bolt

Figure 33. Motor mount bolts.

G0555 14" Ultimate Bandsaw

Image 32
Contents Ultimate Bandsaw Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Bandsaws General Information CommentaryCircuit Requirements 110V Operation 220V OperationGrounding Extension CordsMachine Features Bandsaw FeaturesPiece Inventory SET UPUnpacking Bandsaw unit from Box Hardware Recognition Chart Clean Up Site ConsiderationsAssembling Stand Page To mount the trunnion base Mounting BandsawMounting Trunnion Base Installing Table To install the table on the bandsawTo install the positive stop Positive StopInstalling Fence To install the fenceTo center track the blade Unplug the bandsaw Connecting Dust HoseBlade Tracking Test Run Changes in the blade tension may change the blade trackingAdjusting Support Bearings To adjust the support bearingsTensioning Blade To tension the bandsaw blade016 Adjusting Blade Guides To adjust the upper and lower blade guidesAdjusting Positive Stop Setting Table Tilt Scale to 0˚To set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scaleAligning Table Aligning FenceTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotMiters Angles Compound Angles Resawing Ripping Crosscutting OperationsOverview To adjust guide post assembly alignment on the guide post Table TiltGuide Post To tilt the tableRipping Ripping with a push stick G0555 14 Ultimate BandsawTo resaw a workpiece CrosscuttingResawingTo crosscut with the Model G0555 Cutting Curves Stacked CutsBlade Speed To change the blade speed Unplug the bandsawBlade Width Blade InformationBlade Length Blade Care Tooth StyleTooth Pitch Blade Changes Blade BreakageTo calibrate the scale Scale CalibrationTo replace the blade Maintenance General MaintenanceMiscellaneous LubricationService Adjustments About ServiceChecking V-Belt Tensioning V-BeltReplacing V-Belt To replace the V-belt Unplug the bandsawTo skew your fence Shimming Table Blade LeadTo shim the table Wheel Alignment To verify if the the upper and lower wheels are coplanarCoplanar diagram G0555 14 Ultimate Bandsaw Shimming a wheelModel G0555 Wiring Diagram Troubleshooting Closure Machine Data Sheet 144 148 Base PTS001M Thumb Screw M6-1.0 X Stand TOP Large Fence Rail Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog
Related manuals
Manual 68 pages 40.06 Kb