Gap manual Loading the N75C, To Prevent Accidental Injuries

Page 6

LOADING THE N75C

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

TO PREVENT ACCIDENTAL INJURIES:

Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

Never point the tool at anyone else.

Never engage in horseplay.

Never pull the trigger unless nose is directed at the work.

Always handle the tool with care.

Do not pull the trigger or depress the trip mechanism while loading the tool.

1.Open the magazine:

Pull down door latch and swing door/magazine cover outward. Fig.A

2.Check Adjustment:

The nailer must be set for the length of nail to be used. Nails will not feed smoothly if the magazine is not correctly adjusted. The magazine contains an adjustable nail platform on which the nail coil rests.

The nail platform can be moved up and down to four nail settings.

To change setting twist the post and place into the correct step. Fig.B 1-1/2” (38mm) nails - use 1st step

1-3/4” – 2” (45-50mm) nails - use 2nd step

2-1/4”2-3/8” (55-60mm) nails - use 3rd step 2-1/2” – 3” (65-75mm) nails - use 4th step

3.Load the coil of nails:

Place the coil of nails over the post in the magazine. Uncoil enough nails to reach the feed pawl. Place the first nail in front of the front tooth on the feed pawl, in the driver channel. The nail heads must be in the slot in the nose. Fig. C and Fig. D

NOTE: Use only nails recommended by Bostitch for N75C series nailers or nails which meet Bostitch specifications.

4.Swing cover closed:

To aid in the feeding of plastic collated nails the tab on the cover should be repositioned. To do so apply pressure to the top center of the tab and simultaneously apply pressure to the bottom outer edge of the tab until

it rests on the top outer brim of the cover. Swing the door/magazine cover closed. Check that the latch engages when released. (If it does not engage, check that the nail heads are in the slot in the nose.)

5.Removal of plastic strip:

As nails are driven, the plastic strip will feed out of the tool. When sufficient strip has been fed out, it can be torn away by pulling against the tear edge in the nose. Fig. E

A

B

C

D

E

-6-

Image 6
Contents N75C Limited Warranty IntroductionIndex Loading Tool Safety InstructionsAIR Supply and Connections OperationN75C Tool Specifications Lubrication Loading the N75C To Prevent Accidental InjuriesDIAL-A-DEPTH Fastener Control Adjustment Directional Exhaust DeflectorBostitch Contact Trip Operation Tool OperationBefore Handling or Operating this Tool Sequential Trip OperationAIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Tool Operation CheckTrouble Shooting Problem Cause CorrectionCoil Nailers Accessories Available Nota IntroducciónÍndice Garantia LimitadaAL Cargar LA Herramienta Instrucciones DE SeguridadSuministro DE Aire Y Conexiones OperaciónEspecificaciones DE LA Herramienta N75C Lubricación Cómo Cargar EL N75C Advertencia Para Impedir Lesiones AccidentalesAjuste DEL Control DE Fondo DEL Sujetador DIAL-A-DEPTH Deflector DE Escape DireccionalOperación DE Disp ARO POR Contacto Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Operación DE Disp ARO SecuencialVerificación DE LA Operación DE LA Herramienta Mantenimiento DE LA Herramienta NeumáticaClavadoras DE Bobina ProblemaDiagnóstico DE Falla CausaAccesorios Disponibles Sommaire RemarqueGarantie Limitée Chargement DE L’APPAREIL Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement FonctionnementCaractéristiques DU N75C OpérationLubrification Chargement DU N75C Pour Prévenir UN AccidentDéflecteur DE L’ÉCHAPPEMENT Directionnel Avant DE Manipuler OU D’UTILISER CET Outil Mode D’EMPLOIFonctionnement DE L’APPAREIL Déclenchement À LA Volée 2. Déclenchement AU COUP-PAR-COUPVérification DU Système DE Déclenchement Problèmes DE Fonctionnement Appareil À RouleauProblème Cause Correction Accessoires Disponibles