Gap N75C manual DIAL-A-DEPTH Fastener Control Adjustment, Directional Exhaust Deflector, Bostitch

Page 7

“DIAL-A-DEPTH™” FASTENER CONTROL ADJUSTMENT

The DIAL-A-DEPTH™ Fastener Control adjustment feature provides close control of the fastener drive depth: from flush with the work surface to shallow or deep countersink. First, set the air pressure for consistent drive in the specific work as described on page 4, then use the DIAL-A-DEPTH™ Fastener Control adjustment to give the desired depth of drive.

DIRECTIONAL EXHAUST DEFLECTOR

The adjustable exhaust deflector can be rotated to any desired position by hand without the use of any tools.

Exhaust Deflector

360º

IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANUAL OBSERVE THE FOLLOWING FOR SAFE OPERATION

•Use the BOSTITCH pneumatic tool only for the purpose for which it was designed.

•Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area.

•Do not use the tool as a hammer.

•Always carry the tool by the handle. Never carry the tool by the air hose.

•Do not alter or modify this tool from the original design or function without approval from

BOSTITCH.

•Always be aware that misuse and improper handling of this tool can cause injury to yourself and others.

•Never clamp or tape the trigger or contact trip in an actuated position.

•Never leave a tool unattended with the air hose attached.

•Do not operate this tool if it does not contain a legible WARNING LABEL.

•Do not continue to use a tool that leaks air or does not function properly. Notify your nearest Bostitch representative if your tool continues to experience functional problems.

-7-

Page 6 Page 8
Image 7
Page 6 Page 8
Contents N75C Introduction Limited WarrantyIndex Operation Safety InstructionsAIR Supply and Connections Loading ToolN75C Tool Specifications Lubrication To Prevent Accidental Injuries Loading the N75CDirectional Exhaust Deflector DIAL-A-DEPTH Fastener Control AdjustmentBostitch Sequential Trip Operation Tool OperationBefore Handling or Operating this Tool Contact Trip OperationTool Operation Check Replacement PartsAssembly Procedure for Seals AIR SUPPLY-PRESSURE and VolumeProblem Cause Correction Trouble ShootingCoil Nailers Accessories Available Garantia Limitada IntroducciónÍndice NotaOperación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaEspecificaciones DE LA Herramienta N75C Lubricación Advertencia Para Impedir Lesiones Accidentales Cómo Cargar EL N75CDeflector DE Escape Direccional Ajuste DEL Control DE Fondo DEL Sujetador DIAL-A-DEPTHOperación DE Disp ARO Secuencial Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Operación DE Disp ARO POR ContactoMantenimiento DE LA Herramienta Neumática Verificación DE LA Operación DE LA HerramientaCausa ProblemaDiagnóstico DE Falla Clavadoras DE BobinaAccesorios Disponibles Remarque SommaireGarantie Limitée Fonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILOpération Caractéristiques DU N75CLubrification Pour Prévenir UN Accident Chargement DU N75CDéflecteur DE L’ÉCHAPPEMENT Directionnel Déclenchement À LA Volée 2. Déclenchement AU COUP-PAR-COUP Mode D’EMPLOIFonctionnement DE L’APPAREIL Avant DE Manipuler OU D’UTILISER CET OutilVérification DU Système DE Déclenchement Appareil À Rouleau Problèmes DE FonctionnementProblème Cause Correction Accessoires Disponibles
Top Page Image Contents