Woodstock W1751 owner manual Keep stable footing and balance at all times

Page 9

W1751 25" Wide-Belt Sander

12.Do not force the machine. The machine will do a safer and better job if it does the work.

13.Use the correct tool. Do not force the tool or attachment to do a job for which it was not designed.

14.Wear proper apparel. Do not wear loose clothing, gloves, jewelry, keep long hair tied up, etc.

15.Remove adjusting keys and wrenches. Before turning the machine on, make a habit of checking that all adjusting keys and wrenches have been removed before turning the machine ON.

16.DO NOT use extension cord. Due to the high-amperage draw of this industrial machine, we do not recommend using an extension cord. If you use an extension cord with an undersized gauge or one that is too long, excessive heat will be generated within the circuit increasing the chance of a fire or damage to the circuit.

17.Keep stable footing and balance at all times.

18.Do not leave machine unattended. Wait until it comes to a complete stop before leaving the area.

19.Perform machine maintenance and care. Follow lubrication and accessory attachment instructions in the manual.

20.Keep machine away from open flame. Operating machines near pilot lights and/or open flames creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause an explosion. Do not operate the machine in high-risk areas, including but not limited to, those mentioned above.

21.If at any time you are experiencing difficulties performing the intended operation, stop using the machine! Then contact our Service Department or ask a qualified expert how the operation should be performed.

22.Habits—good and bad—are hard to break. Develop good habits in your shop and safety will become second-nature to you.

ALWAYS wear your respirator in addition to using a dust collector. This machine produces sawdust that may cause allergic reactions or respiratory problems.

SAFETY

-7-

Image 9
Contents WIDE-BELT Sander Page Contents Service Woodstock Technical Support IntroductionSpecifications Controls and Features Disconnect machine when cleaning, adjusting or servicing Standard Safety InstructionsKeep stable footing and balance at all times Additional Safety Instructions for Sanders 220V Operation Extension CordsGrounding Unpacking Box ContentsCleaning Machine Machine PlacementAssembly PlatenHandwheel Crank Ducting Air SupplySanding Belt Tensioning Sanding Belt InstallationPressure Roller Depth and Alignment To adjust the pressure rollers, do these stepsPressure Roller Tension Pressure roller adjusterConveyor Belt Start and Stop Buttons Control PanelSanding Load Amp Meter Sanding Belt Start and Stop ButtonsGeneral Operation Test RunTo complete the test run, do these steps Setting Feed Speed Using the Amp Draw MeterTo change the conveyor belt speed do these steps Changing Sanding Belts Emergency StopTo use the emergency stop, do these steps Basic Sanding Using the PlatenTip To sand a workpiece, do these stepsOperations Jet Air Flow To adjust the jet air flow, do these stepsBelt tracking knob and lever Belt TrackingBelt Oscillation Speed Belt Tracking procedure on Page 24 or the JetGeneral Cleaning BeltsLubrication Maintaining Air SystemBrake Service To check the condition of the brake pads, do these stepsTo replace the brake pads, do these steps Change the V-belt as follows Changing V-BeltsTo tension the V-belts, do these steps Belt TensionConveyor Belt Tension Tracking Conveyor belt tension Tracking adjustment locationsGauge boards placed under Pressure rollers Pressure RollersTo adjust the belt tracking limit switches, do these steps Belt Tracking Limit SwitchMotor & Electrical TroubleshootingSanding and Results See Figure Electrical Box Component LocationsEmergency Digital amp Power lampW1751 Limit Switch Wiring Diagram W1751 General Wiring Diagram Sanding Motor PART# Description Parts ListConveyor System Conveyortable Upper Contactrollerbase Sanding DrumSystem BALLBEARING6005ZZ Upper Machineframe Parts Air System Parts ListDescription Electrical Connections BoxAccessories Accessories List Labels List Label PlacementWarranty Comments Warranty RegistrationBOX BELLINGHAM, WA