Woodstock W1712 instruction manual #16 #14 11-12 13-16 #12 17-20 #10 21-30

Page 7

12.DO NOT force tool. The machine will do a safer and better job at the rate for which it was designed.

13.Use correct tool. DO NOT force machine or attachment to do a job for which it was not designed.

14.Wear proper apparel. DO NOT wear loose clothing, neck ties, gloves, jewelry, and secure long hair away from moving parts.

15.Remove adjusting keys, rags, and tools. Before turning the machine on, make it a habit to check that all adjusting keys and wrenches have been removed.

16.Avoid using an extension cord. But if you must, examine the extension cord to ensure it is in good condition. Use TABLE 1 below to determine the correct length and gauge of extension cord needed for your particular needs. The amp rating of the motor can be found on its nameplate. If the motor is dual voltage, be sure to use the amp rating for the voltage you will be using. If you use an exten- sion cord with an undersized gauge or one that is too long, excessive heat will be generated within the circuit, increasing the chance of a fire or damage to the circuit. Always use an extension cord that uses a ground pin and connected ground wire. Immediately replace a damaged extension cord.

17.Keep proper footing and balance at all times and lock mobile base from rolling freely before using your machine.

18.DO NOT leave machine unattended. Wait until it comes to a complete stop before leaving the area.

19.Perform machine maintenance and care. Follow lubrication and accessory attachment instructions in the manual.

20.Keep machine away from open flame. Operating machines near pilot lights or open flames creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause an explo- sion. DO NOT operate the machine in high-risk areas, including but not limited to, those mentioned above.

21.If at any time you are experiencing difficulties performing the intended operation, stop using the machine! Contact our service department or ask a qualified expert how the operation should be per- formed.

22.Habits are hard to break. Develop good habits in your shop and consistent safety practices will become second-nature to you.

SAFETY

TABLE 1.

Extension Cord Requirements

 

Length And Gauge

Amp Rating

25ft

50ft

100ft

0-6

#16

#16

#16

7-10

#16

#16

#14

11-12

#16

#16

#14

13-16

#14

#12

#12

17-20

#12

#12

#10

21-30

#10

#10

No

Operating this equipment creates the potential for flying debris to cause eye injury. Always wear safety glasses or gog- gles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI).

-5-

Image 7
Contents Disc & 6 Belt Sander Page Contents Introduction Woodstock Service and SupportAbout Your New Sander Specifications Warranty and ReturnsStandard Safety Instructions Safety#16 #14 11-12 13-16 #12 17-20 #10 21-30 Know Your Machine Safety Instructions for Your Sander Extension Cords 110V OperationGrounding Unpacking AssemblyInventory Shop Preparation Initial CleaningDust Collection To assemble the cabinet stand, do these steps Cabinet AssemblyKeep the Sander Unplugged Mounting SanderInstalling table Installing TableBelt Tracking AdjustmentsTable tilting knob Scale Pointer Machinists Square Table Angle AdjustmentDisc Table Alignment Disc table adjustment bolts Only 2 of 4 shownTest Run OperationsBelt/Disc Selection Power SwitchMiter Sanding Flat Sanding Disc SandingCap screw location Work-Stop Fence Removing belt guard Table and Mounting Bracket Changing Sanding BeltChanging Sanding Disc Paper Sanding disc installationSanding Surfaces MaintenanceGeneral Table And BaseParts Parts Description Description Troubleshooting Sanding Parts Parts Warranty Card Woodstock INTERNATIONAL, INC