Woodstock W1761/W1762 owner manual Optional Table Insert, D3697-Standard Zero-Clearance Insert

Page 11

Model W1761/W1762 (M-1/10, S7/10+)

Optional Table Insert

Zero clearance inserts reduce tearout and increase user safety. These inserts can be customized to fit a specific blade height or blade angle for the applicable cutting operation.

Zero-clearance table inserts may be available for the Model W1761/W1762 through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, a zero-clearance insert can be purchased through an online dealer. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at:

1-800-840-8420 or at sales@woodstockint.com.

If you plan on using a dado blade with your saw, you need to purchase an additional zero-clearance table insert for the dado blade.

IMPORTANT: Zero-clearance inserts cut with a dado blade should not be used later with a standard blade. Not only will you lose the benefits of having zero clearance, the large gaps around the blade could increase your risk of injury. For this reason, we strongly recommend that you have a dedicated table insert for each dado width.

D3697—Standard Zero-Clearance Insert

NOTICE

Refer to the newest copy of the Woodstock International, Inc. Catalog or http://www.shopfox. biz for other safety accessories available for this machine.

-10-

Image 11

Contents Table SAW with Riving Knife Inventory Differences Important Changes to AssemblyBlade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Location to secure blade guard Screw Installing Blade Guard & SpreaderTo remove the pawls, do these steps Anti-Kickback PawlsWhen Not to Use the Blade Guard When to Use the Blade GuardRiving Knife Installing Riving KnifeWhen to Use the Riving Knife When Not to Use the Riving KnifeTools Needed Spreader or Riving Knife AlignmentChecking Alignment Follow Checking Alignment, Steps 1-4, on Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Possible Tools NeededD3697-Standard Zero-Clearance Insert Optional Table InsertDescription New Parts=\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself from Kickback Do not stand directly behind Blade when making a cutCommon Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications Electrical Specifications W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Phase ConverterImmediately discard all Plastic bags and pack Items Needed for Set UpUnpacking Description QtyBox Inventory Figure InventoryMachine Inventory Fence InventoryExtension Table Inventory Fence Rail InventoryMachine Placement Cleaning MachineExtension Table To install the front and rear rails, do these stepsLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To change the arbor, do these steps To install the blade, do these stepsSaw Blade ArborBlade Guard & Splitter To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Table InsertSplitter To install the riving knife, do these stepsMiter Gauge ON/OFF SwitchTo install the switch, do these steps To install the miter gauge, do these stepsRecommended CFM at Dust Port Recommended AdjustmentsRecommended adjustment checklist Dust CollectionTo test run the machine, do these steps Test RunBasic Controls GeneralBlade Selection Disabling On/Off SwitchRipping blade features see Figure Crosscut blade features see FigureDado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Through Cuts Workpiece InspectionNon-Through Through Cuts Non-Through CutsTypical ripping operation RippingCrosscutting To make a crosscut using the miter gauge, do these stepsTo perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts To use a stacked or wobble dado blade, do these steps Dado CuttingDisconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet CuttingFirst cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingTo build the auxiliary fence, do these steps Auxiliary FenceTo perform resawing operations, do these steps Resawing OperationsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Weekly Check CleaningLubrication Daily CheckMotor & Electrical TroubleshootingW1761/W1762 12 Table Saw with Riving Knife OperationsTo remove the flat belt, do these steps Replacing Flat BeltDeflect it no more than 1⁄8 To install the new belt, do these stepsTo set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Miter Slot to Blade Parallelism Example of adjusting blade to Miter slotBlade Alignment To adjust the blade by moving the table, do these stepsClamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram W1761 magnetic switch SwitchSee Figure W1761 Wiring DiagramW1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phaseW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts ListFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts ListMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA