Woodstock W1761/W1762 Digital Readout, To adjust the tilt indicator arrow, do these steps

Page 64

W1761/W1762 12" Table Saw with Riving Knife

3.Move the blade angle to 30°, or remove the panel on the right side of the cabinet to access the 45° stop bolt.

4.Using a 12mm wrench, loosen the jam nut (Figure 67) on the 45° stop bolt, adjust the stop bolt up or down, then check to see if the blade is 45° to the table.

5.Continue adjusting the stop bolt until it contacts the cabinet when the blade is at 45°.

6.Tighten the jam nut.

To adjust the tilt indicator arrow, do these steps:

1.Set the 90° stop bolt (see instructions on Page 49).

2.Loosen the blade height handwheel set screw and remove the handwheel.

3.Loosen the Phillips head screw shown in Figure 68 and move the tip of the indicator to 0°.

4.Tighten the Phillips head screw and reinstall the handwheel.

Digital Readout

45° Stop Bolt

Jam Nut

Figure 67. 45° stop bolt and jam nut.

Indicator

Phillips Head

Screw

SERVICE

The digital readout displays the current blade angle. We recommend you set the readout after verifying the 90° and 45° blade tilt stops.

To set the digital readout, do these steps:

1.Ensure the 90° stop bolt is set (see Blade Tilt Stops on Page 49.

2.Move the blade angle to 0° and press the 0° SET button (Figure 69) for several seconds until the readout displays 0.00.

3.Move the blade angle to 45° and press the SET but- ton for several seconds until the readout displays 45.0.

Note: If you move the blade angle handwheel when the power is disconnected, the digital readout will be incorrect when the saw is reconnected.

Figure 68. Tilt indicator arrow.

0° Set Button

45° Set Button

Figure 69. Digital readout.

-50-

Image 64

Contents Table SAW with Riving Knife Important Changes to Assembly Inventory DifferencesBlade Requirements Blade InstallationBlade Size Requirements Guard Blade GuardSpreader Installing Blade Guard & Spreader Location to secure blade guard ScrewAnti-Kickback Pawls To remove the pawls, do these stepsWhen to Use the Blade Guard When Not to Use the Blade GuardInstalling Riving Knife When to Use the Riving KnifeWhen Not to Use the Riving Knife Riving KnifeChecking Alignment Spreader or Riving Knife AlignmentTools Needed Adjusting Alignment Adjusting Bent Spreader/Riving KnifePossible Tools Needed Follow Checking Alignment, Steps 1-4, onOptional Table Insert D3697-Standard Zero-Clearance InsertNew Parts Description=\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickbackDo not stand directly behind Blade when making a cut Protecting Yourself from KickbackCommon Terms W1761 Electrical Specifications W1761 220V Single-Phase OperationExtension Cords W1762 220V 3-Phase Operation W1762 440V 3-Phase OperationPhase Converter Electrical SpecificationsItems Needed for Set Up UnpackingDescription Qty Immediately discard all Plastic bags and packInventory Machine InventoryFence Inventory Box Inventory FigureFence Rail Inventory Extension Table InventoryCleaning Machine Machine PlacementTo install the front and rear rails, do these steps Extension TableLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To install the blade, do these steps Saw BladeArbor To change the arbor, do these stepsTo install and adjust the table insert, do these steps To install the blade guard, do these stepsTable Insert Blade Guard & SplitterTo install the riving knife, do these steps SplitterON/OFF Switch To install the switch, do these stepsTo install the miter gauge, do these steps Miter GaugeRecommended Adjustments Recommended adjustment checklistDust Collection Recommended CFM at Dust PortTest Run To test run the machine, do these stepsGeneral Basic ControlsDisabling On/Off Switch Ripping blade features see FigureCrosscut blade features see Figure Blade SelectionLaminate blade features see Figure Combination blade features see FigureDado Blades see Figure Workpiece Inspection Non-Through Through CutsNon-Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge, do these steps CrosscuttingBlade Tilt & Bevel Cuts Miter CutsTo perform a miter cut, do these steps Dado Cutting To use a stacked or wobble dado blade, do these stepsDisconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard bladeResawing Resaw BarrierAuxiliary Fence To build the auxiliary fence, do these stepsResawing Operations To perform resawing operations, do these stepsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Cleaning LubricationDaily Check Weekly CheckTroubleshooting Motor & ElectricalOperations W1761/W1762 12 Table Saw with Riving KnifeReplacing Flat Belt To remove the flat belt, do these stepsTo install the new belt, do these steps Deflect it no more than 1⁄8To set the 90 stop bolt, do these steps Blade Tilt StopsTo set the 45 stop bolt, do these steps Digital Readout To adjust the tilt indicator arrow, do these stepsTo set the digital readout, do these steps Example of adjusting blade to Miter slot Miter Slot to Blade ParallelismTo adjust the blade by moving the table, do these steps Blade AlignmentSquare and Height Adjusting FenceClamping Pressure and Parallelism Miter gauge diagram Switch W1761 magnetic switchW1761 Wiring Diagram See FigureW1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical ComponentsW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List PartsFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List MotoraccesscoverMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA