Woodstock W1761/W1762 owner manual D3585 Bore General Purpose D3586 Fine Finishing D3587 100

Page 56

OPERATIONS

W1761/W1762 12" Table Saw with Riving Knife

The Model D3588 Shop Fox 8" Carbide-Tipped Stacking Dado Blade Set cuts dados from 1⁄8" to 3⁄4". Solid body chip cutting blanks pro- vide more mass and better balance. Five-tooth chip cutters provide more cuts per revolution. 5⁄8" bore.

The D3585 Shop Fox Carbide-Tipped ATB Saw Blades woodworking blades set a new standard for quality and value. These are excellent industrial-quality blades designed for heavy use, long life, and pre- cise accuracy.

Model

Blade Size

Hole Size

No. of Teeth

Application

D3585

12"

1" Bore

60

General Purpose

D3586

12"

1" Bore

80

Fine Finishing

D3587

12"

1" Bore

100

Super Fine Work

The Model D3207 Magnetic Base with Dial Indicator in Case is the best value in precision measuring instruments. Powerful magnetic base with infinitely adjustable control arm, fine tuning beam and magnetic switch. Add to this the 1" travel dial indicator with divi- sions of 0.001", 0.100" per revolution, and a 0.100" counter and any setup job is a snap.

Power Feeders will make light work out of those big jobs with

greater accuracy and safety. The Model W1765 features a 1⁄4 HP, W1765 110V, 1.8 Amp motor. The Model W1766 features a 1⁄2 HP, 220V, 4

Amp motor. Both models feature forward/reverse, XYZ adjustment, multiple feed speeds, and synthetic rubber wheels.

W1766

-42-

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Table SAW with Riving Knife Important Changes to Assembly Inventory DifferencesBlade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Installing Blade Guard & Spreader Location to secure blade guard ScrewAnti-Kickback Pawls To remove the pawls, do these stepsWhen to Use the Blade Guard When Not to Use the Blade GuardInstalling Riving Knife When to Use the Riving KnifeWhen Not to Use the Riving Knife Riving KnifeTools Needed Spreader or Riving Knife AlignmentChecking Alignment Adjusting Alignment Adjusting Bent Spreader/Riving KnifePossible Tools Needed Follow Checking Alignment, Steps 1-4, onOptional Table Insert D3697-Standard Zero-Clearance InsertNew Parts Description=\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickbackDo not stand directly behind Blade when making a cut Protecting Yourself from KickbackCommon Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications W1762 220V 3-Phase Operation W1762 440V 3-Phase OperationPhase Converter Electrical SpecificationsItems Needed for Set Up UnpackingDescription Qty Immediately discard all Plastic bags and packInventory Machine InventoryFence Inventory Box Inventory FigureFence Rail Inventory Extension Table InventoryCleaning Machine Machine PlacementTo install the front and rear rails, do these steps Extension TableLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To install the blade, do these steps Saw BladeArbor To change the arbor, do these stepsTo install and adjust the table insert, do these steps To install the blade guard, do these stepsTable Insert Blade Guard & SplitterTo install the riving knife, do these steps SplitterON/OFF Switch To install the switch, do these stepsTo install the miter gauge, do these steps Miter GaugeRecommended Adjustments Recommended adjustment checklistDust Collection Recommended CFM at Dust PortTest Run To test run the machine, do these stepsGeneral Basic ControlsDisabling On/Off Switch Ripping blade features see FigureCrosscut blade features see Figure Blade SelectionDado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Workpiece Inspection Non-Through Through CutsNon-Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge, do these steps CrosscuttingTo perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts Dado Cutting To use a stacked or wobble dado blade, do these stepsDisconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard bladeResawing Resaw BarrierAuxiliary Fence To build the auxiliary fence, do these stepsResawing Operations To perform resawing operations, do these stepsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Cleaning LubricationDaily Check Weekly CheckTroubleshooting Motor & ElectricalOperations W1761/W1762 12 Table Saw with Riving KnifeReplacing Flat Belt To remove the flat belt, do these stepsTo install the new belt, do these steps Deflect it no more than 1⁄8To set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Example of adjusting blade to Miter slot Miter Slot to Blade ParallelismTo adjust the blade by moving the table, do these steps Blade AlignmentClamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram Switch W1761 magnetic switchW1761 Wiring Diagram See FigureW1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical ComponentsW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List PartsFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List MotoraccesscoverMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA
Top Page Image Contents