Woodstock W1761/W1762 owner manual Fence Rail Inventory, Extension Table Inventory

Page 30

W1761/W1762 12" Table Saw with Riving Knife

Fence Rail Inventory

SET UP

Box Inventory: (Figure 11)		Qty
A.	Fence Tube (93" Long)	1
B.	Rear Rail (79" Long)	1
C.	Front Rail (93" Long)	1
Extension Table Inventory
Box Inventory: (Figure 12)		Qty
A.	Extension Table	1
B.	Lower Shelf	1
C.	Shelf End Plate	1
D.	Support Legs	2
E.	Lower Shelf Brackets	2
Tools and Hardware (Not Shown):		Qty
•	Cap Screws M8-1.25 x 25
	(Rear Rail/Table/Ext. Table)	8
•	Lock Washers 8mm
	(Rear Rail/Table/Ext. Table)	10

•Flat Head Screws M8-1.25 x 25

	(Front Rail/Table/Ext. Table)	8
•	Flat Washers 8mm
	(Front Rail/Ext. Table/Rear Rail)	14
•	Hex Nuts M8-1.25
	(Front Rail/Ext. Table/Rear Rail)	8
•	Hex Nuts M6-1
	(Brackets/Shelf End Plate)	2
• Hex Bolts M6-1 x 12		4
	(Cabinet/Lower Shelf Brackets/Shelf End Plate)
• Phillip Head Screws M6-1 x 12
	(Ext. Table/Legs/End Plate)	12
•	Flat Washers 6mm
	(Ext. Table/Legs/End Plate)	16
• Feet 3/8"-16 x 2 (Legs)		2
• Hex Nuts 3/8-16 (Feet)		2
• Flat Washers 10mm (Cabinet)		2
• Hex Bolts M10-1.5 x 25 (Cabinet)		2
• Flange Bolts M8-1.25 x 12
	(Tube/Front Rail)	9

A

CB

Figure 11. Fence rail components.

A

B

E

D

C

Figure 12. Extension table components.

-16-

Image 30

Contents Table SAW with Riving Knife Important Changes to Assembly Inventory DifferencesBlade Installation Blade RequirementsBlade Size Requirements Blade Guard GuardSpreader Installing Blade Guard & Spreader Location to secure blade guard ScrewAnti-Kickback Pawls To remove the pawls, do these stepsWhen to Use the Blade Guard When Not to Use the Blade GuardWhen Not to Use the Riving Knife Installing Riving KnifeWhen to Use the Riving Knife Riving KnifeSpreader or Riving Knife Alignment Checking AlignmentTools Needed Possible Tools Needed Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Follow Checking Alignment, Steps 1-4, onOptional Table Insert D3697-Standard Zero-Clearance InsertNew Parts Description=\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickbackDo not stand directly behind Blade when making a cut Protecting Yourself from KickbackCommon Terms W1761 220V Single-Phase Operation W1761 Electrical SpecificationsExtension Cords Phase Converter W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Electrical SpecificationsDescription Qty Items Needed for Set UpUnpacking Immediately discard all Plastic bags and packFence Inventory InventoryMachine Inventory Box Inventory FigureFence Rail Inventory Extension Table InventoryCleaning Machine Machine PlacementTo install the front and rear rails, do these steps Extension TableLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Arbor To install the blade, do these stepsSaw Blade To change the arbor, do these stepsTable Insert To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Blade Guard & SplitterTo install the riving knife, do these steps SplitterTo install the miter gauge, do these steps ON/OFF SwitchTo install the switch, do these steps Miter GaugeDust Collection Recommended AdjustmentsRecommended adjustment checklist Recommended CFM at Dust PortTest Run To test run the machine, do these stepsGeneral Basic ControlsCrosscut blade features see Figure Disabling On/Off SwitchRipping blade features see Figure Blade SelectionCombination blade features see Figure Laminate blade features see FigureDado Blades see Figure Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge, do these steps CrosscuttingMiter Cuts Blade Tilt & Bevel CutsTo perform a miter cut, do these steps Dado Cutting To use a stacked or wobble dado blade, do these stepsDisconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard bladeResawing Resaw BarrierAuxiliary Fence To build the auxiliary fence, do these stepsResawing Operations To perform resawing operations, do these stepsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Daily Check CleaningLubrication Weekly CheckTroubleshooting Motor & ElectricalOperations W1761/W1762 12 Table Saw with Riving KnifeReplacing Flat Belt To remove the flat belt, do these stepsTo install the new belt, do these steps Deflect it no more than 1⁄8Blade Tilt Stops To set the 90 stop bolt, do these stepsTo set the 45 stop bolt, do these steps To adjust the tilt indicator arrow, do these steps Digital ReadoutTo set the digital readout, do these steps Example of adjusting blade to Miter slot Miter Slot to Blade ParallelismTo adjust the blade by moving the table, do these steps Blade AlignmentAdjusting Fence Square and HeightClamping Pressure and Parallelism Miter gauge diagram Switch W1761 magnetic switchW1761 Wiring Diagram See FigureW1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical ComponentsW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List PartsFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List MotoraccesscoverMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA