Woodstock W1761/W1762 owner manual Miter gauge diagram

Page 68

W1761/W1762 12" Table Saw with Riving Knife

Miter Gauge

To adjust the miter gauge so it is perpendicular to the saw blade, do these steps:

1.	Slide the miter gauge into the miter gauge slot to
	the left of the blade.
2.	Push in the shaft (Figure 77).
3.	Loosen the lock knob on the miter gauge and place
	a square against the face of the miter body and the
	blade.
4.	Adjust the miter body until the pointer is at 0° and
	there is no space between the square and the blade,

	Stop	Jam
	Screw	Jam
	Screw	Nut
		Nut
	Pointer
	Shaft

Miter Body

Lock Knob

	then tighten the lock knob.
5.	Loosen the jam nut with an 8mm wrench and adjust
	the stop screw until it is seated against the shaft
	(see Figure 77 for part locations), then tighten the
	jam nut.
6.	Loosen the screw on the front of the miter bar,
	adjust the pointer to 0°, then tighten the screw.
7.	To adjust to 45°, follow Steps 1-5using an adjust-
	able square set to 45°.
8.	Double-check your adjustments at 45° and 90°
	to assure that you have accurately set your miter
	gauge.
9.	To fit the miter bar tighter in the miter slot, turn
	the adjustment set screws shown in Figure 77 clock-
	wise in small increments with a 2.5mm hex wrench,
	and test fit between adjustments until the miter
	gauge fits your expectations.

SERVICE

Set

Screws

Figure 77. Miter gauge diagram.

-54-

Image 68

Contents Table SAW with Riving Knife Important Changes to Assembly Inventory DifferencesBlade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Installing Blade Guard & Spreader Location to secure blade guard ScrewAnti-Kickback Pawls To remove the pawls, do these stepsWhen to Use the Blade Guard When Not to Use the Blade GuardInstalling Riving Knife When to Use the Riving KnifeWhen Not to Use the Riving Knife Riving KnifeTools Needed Spreader or Riving Knife AlignmentChecking Alignment Adjusting Alignment Adjusting Bent Spreader/Riving KnifePossible Tools Needed Follow Checking Alignment, Steps 1-4, onOptional Table Insert D3697-Standard Zero-Clearance InsertNew Parts Description=\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickbackDo not stand directly behind Blade when making a cut Protecting Yourself from KickbackCommon Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications W1762 220V 3-Phase Operation W1762 440V 3-Phase OperationPhase Converter Electrical SpecificationsItems Needed for Set Up UnpackingDescription Qty Immediately discard all Plastic bags and packInventory Machine InventoryFence Inventory Box Inventory FigureFence Rail Inventory Extension Table InventoryCleaning Machine Machine PlacementTo install the front and rear rails, do these steps Extension TableLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To install the blade, do these steps Saw BladeArbor To change the arbor, do these stepsTo install and adjust the table insert, do these steps To install the blade guard, do these stepsTable Insert Blade Guard & SplitterTo install the riving knife, do these steps SplitterON/OFF Switch To install the switch, do these stepsTo install the miter gauge, do these steps Miter GaugeRecommended Adjustments Recommended adjustment checklistDust Collection Recommended CFM at Dust PortTest Run To test run the machine, do these stepsGeneral Basic ControlsDisabling On/Off Switch Ripping blade features see FigureCrosscut blade features see Figure Blade SelectionDado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Workpiece Inspection Non-Through Through CutsNon-Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge, do these steps CrosscuttingTo perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts Dado Cutting To use a stacked or wobble dado blade, do these stepsDisconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard bladeResawing Resaw BarrierAuxiliary Fence To build the auxiliary fence, do these stepsResawing Operations To perform resawing operations, do these stepsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Cleaning LubricationDaily Check Weekly CheckTroubleshooting Motor & ElectricalOperations W1761/W1762 12 Table Saw with Riving KnifeReplacing Flat Belt To remove the flat belt, do these stepsTo install the new belt, do these steps Deflect it no more than 1⁄8To set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Example of adjusting blade to Miter slot Miter Slot to Blade ParallelismTo adjust the blade by moving the table, do these steps Blade AlignmentClamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram Switch W1761 magnetic switchW1761 Wiring Diagram See FigureW1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical ComponentsW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List PartsFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List MotoraccesscoverMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA