Woodstock W1761/W1762 owner manual Switch, W1761 magnetic switch

Page 69

W1761/W1762 12" Table Saw with Riving Knife

W1761/W1762 Electrical Components

Figure 78. W1761 motor junction box, 220V

single-phase.

Figure 79. W1762 motor junction box, 220V 3-

phase.

Figure 81. Digital readout and angle sensor.

SERVICE

Figure 80. Switch.

Figure 82. W1761 magnetic switch.

-55-

Image 69

Contents Table SAW with Riving Knife Inventory Differences Important Changes to AssemblyBlade Installation Blade RequirementsBlade Size Requirements Blade Guard GuardSpreader Location to secure blade guard Screw Installing Blade Guard & SpreaderTo remove the pawls, do these steps Anti-Kickback PawlsWhen Not to Use the Blade Guard When to Use the Blade GuardWhen to Use the Riving Knife Installing Riving KnifeWhen Not to Use the Riving Knife Riving KnifeSpreader or Riving Knife Alignment Checking AlignmentTools Needed Adjusting Bent Spreader/Riving Knife Adjusting AlignmentPossible Tools Needed Follow Checking Alignment, Steps 1-4, onD3697-Standard Zero-Clearance Insert Optional Table InsertDescription New Parts=\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself from Kickback Do not stand directly behind Blade when making a cutCommon Terms W1761 220V Single-Phase Operation W1761 Electrical SpecificationsExtension Cords W1762 440V 3-Phase Operation W1762 220V 3-Phase OperationPhase Converter Electrical SpecificationsUnpacking Items Needed for Set UpDescription Qty Immediately discard all Plastic bags and packMachine Inventory InventoryFence Inventory Box Inventory FigureExtension Table Inventory Fence Rail InventoryMachine Placement Cleaning MachineExtension Table To install the front and rear rails, do these stepsLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Saw Blade To install the blade, do these stepsArbor To change the arbor, do these stepsTo install the blade guard, do these steps To install and adjust the table insert, do these stepsTable Insert Blade Guard & SplitterSplitter To install the riving knife, do these stepsTo install the switch, do these steps ON/OFF SwitchTo install the miter gauge, do these steps Miter GaugeRecommended adjustment checklist Recommended AdjustmentsDust Collection Recommended CFM at Dust PortTo test run the machine, do these steps Test RunBasic Controls GeneralRipping blade features see Figure Disabling On/Off SwitchCrosscut blade features see Figure Blade SelectionCombination blade features see Figure Laminate blade features see FigureDado Blades see Figure Non-Through Through Cuts Workpiece InspectionNon-Through Cuts Through CutsTypical ripping operation RippingCrosscutting To make a crosscut using the miter gauge, do these stepsMiter Cuts Blade Tilt & Bevel CutsTo perform a miter cut, do these steps To use a stacked or wobble dado blade, do these steps Dado CuttingDisconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet CuttingFirst cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingTo build the auxiliary fence, do these steps Auxiliary FenceTo perform resawing operations, do these steps Resawing OperationsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Lubrication CleaningDaily Check Weekly CheckMotor & Electrical TroubleshootingW1761/W1762 12 Table Saw with Riving Knife OperationsTo remove the flat belt, do these steps Replacing Flat BeltDeflect it no more than 1⁄8 To install the new belt, do these stepsBlade Tilt Stops To set the 90 stop bolt, do these stepsTo set the 45 stop bolt, do these steps To adjust the tilt indicator arrow, do these steps Digital ReadoutTo set the digital readout, do these steps Miter Slot to Blade Parallelism Example of adjusting blade to Miter slotBlade Alignment To adjust the blade by moving the table, do these stepsAdjusting Fence Square and HeightClamping Pressure and Parallelism Miter gauge diagram W1761 magnetic switch SwitchSee Figure W1761 Wiring DiagramW1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phaseW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts ListFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts ListMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA