Oilless Compressors
FP2048, FP2049
General Safety Information (Continued)
3.Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.
4.Keep visitors away and NEVER allow children in the work area.
5.Wear safety glasses
and use hearing protection when operating the pump or unit.
!DANGER
Never attempt to repair or modify a tank! Welding, drilling or any
other modification will weaken the tank resulting in damage from rupture or explosion. Always replace worn or damaged tanks.
Drain liquid from
! WARNING tank daily.
13. Tanks rust from moisture |
which weakens the tank. Make sure |
to drain tank daily and inspect |
Installation
LOCATION
It is extremely important to use the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than 100°F.
A minimum clearance of 18 inches between the compressor and a wall is required because objects could obstruct air flow.
Do not locate the
! CAUTION compressor air inlet near steam, paint spray, sandblast
Para Ordenar Repuestos Sírvase Llamar al Distribuidor Mas Cercano A Su Domicilio
Sírvase darnos la siguiente información: | Puede escribirnos a: |
Campbell Hausfeld / Attn: Parts Department | |
100 Production Drive | |
Harrison, OH 45030 U.S.A. | |
| 2a |
| 7 |
14 | 1 |
16 | 12 |
|
6.Do not stand on or use the pump or unit as a handhold.
7.Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using.
8.Check all fasteners at frequent intervals for proper tightness.
! WARNING
Motors, electrical equipment and controls
can cause electrical arcs
that will ignite a flammable gas or vapor. Never operate or repair in or near a flammable gas or vapor. Never store flammable liquids or gases in the vicinity of the compressor.
!CAUTION
Compressor parts may
periodically for unsafe conditions |
such as rust formation and |
corrosion. |
14. Fast moving air will stir up dust and |
debris which may be harmful. Release |
air slowly when draining moisture or |
depressurizing the compressor system. |
SPRAYING PRECAUTIONS
! WARNING
Do not spray flammable materials in vicinity of open flame or near ignition sources including the compressor unit.
15.Do not smoke when spraying paint, insecticides, or other flammable substances.
16.Use a face mask/
respirator when
areas or any other source of contamination. This debris will damage the motor.
GROUNDING INSTRUCTIONS
1. This product is for use on a nominal |
120 volt circuit and has a grounding |
plug that looks like the plug illustrated |
in Fig. 1. Make sure the product is |
connected to an outlet having the |
same configuration as the plug. This |
product must be grounded. In the |
event of an electrical short circuit, |
grounding reduces risk of electrical |
shock by providing an escape wire for |
electric current. This product is |
equipped with a cord having a |
grounding wire with an appropriate |
grounding plug. Plug must be plugged |
into an outlet that is properly installed |
and grounded in accordance with all |
|
| 2b |
|
| 11 |
9 |
| 20 |
|
| |
| 3 | 15 |
|
| |
| 4 |
|
6
5
13
2b
19a
19b
18b
18a
10
22
be hot even if the unit is stopped.
spraying and spray in a well ventilated area
local codes and ordinances. |
Liste de Repuestos
21
8
FP204800, FP204900
9. Keep fingers away from a running |
compressor; fast moving and hot |
to prevent health and fire hazards.
17. Do not direct paint or other sprayed |
Grounding
Pin
No. de | Numero |
| No. de | Numero |
|
Ref. Descripción | de pieza | Ctd. | Ref. Descripción | de pieza | Ctd. |
parts will cause injury and/or burns. |
10. If the equipment should start to |
abnormally vibrate, STOP the |
engine/motor and check |
immediately for the cause. Vibration |
is generally a warning of trouble. |
11. To reduce fire hazard, keep |
engine/motor exterior free of oil, |
solvent, or excessive grease. |
Never remove or ! WARNING attempt to adjust
safety valve. Keep safety valve free from paint and other accumulations.
material at the compressor. Locate |
compressor as far away from the |
spraying area as possible to |
minimize overspray accumulation |
on the compressor. |
18. When spraying or cleaning with |
solvents or toxic chemicals, follow |
the instructions provided by the |
chemical manufacturer. |
TEST RESET
Grounded Outlet
Figure 1 - Grounding Method
!DANGER
Improper use of grounding plug can result in a possible risk of electrical shock!
1 | Cubierta con mango | FP204822AV | 1 |
2 (a, b) |
|
| |
| Ensamblaje del mango | FP204823AV | 1 |
3 | Manómetro del tanque | FP204012AV | 1 |
4 | Regulador | FP204013AV | 1 |
5 | Múltiple | FP204835AV | 1 |
6 | Válvula de seguridad | 1 | |
7 | Interruptor | FP204824AV | 1 |
8 | Llave de drenaje | 1 | |
9 | Ensamblaje de la bomba/motor | FP204825AV | 1 |
10 | Presostato | FP204836AV | 1 |
11 | Kit de tubo de escape | FP204826AV | 1 |
12 | Tornillos de la tapa - | Artículo estándar |
|
| de ferretería | 4 | |
13 | Manguera de 7,6 m (25 pies) | MP302700AV | 1 |
14 | Juego de herramientas (5 piezas)FP204008AV | 1 | |
15 | Válvula de chequeo | FP204827AV | 1 |
16 | Cubierta de almacenamiento | FP204828AV | 1 |
17 | Juego de etiqueta adhesiva |
|
|
| (no se muestra) | FP204829AV | 1 |
18 (a, b) |
|
| |
| Kit de aislador | FP204830AV | 1 |
19 (a, b) |
|
| |
| Guarda de bomba/motor | FP204831AV | 1 |
20 | Filtro | FP204832AV | 1 |
21 | Patas de caucho | FP204833AV | 1 |
22 | Cordón eléctrico | FP204834AV | 1 |
www.chpower.com
2 | 23 Sp |