Delta DLKC6580V2-1 Motor Pulley/Flywheel Alignment, Air Compressor Pump Intake and Exhaust Valves

Page 19

Motor Pulley/Flywheel

Alignment

NOTE: Once the motor pulley has been moved from its factory set loca- tion, the grooves of the flywheel and pulley must be aligned to within 1/16” to prevent excessive belt wear. The air compressor flywheel and motor pulley must be in-line (in the same plane) within 1/16” to assure belt retention within flywheel belt grooves. To check alignment, per- form the following steps:

1.Turn air compressor off, lock out the power supply, and relieve all air pressure from the air tank.

2.Remove belt guard

3.Place a straightedge against the outside of the flywheel and the motor drive pulley.

4.Measure the distance between the edge of the belt and the straightedge at points A1 and A2 in figure. The difference between measurements should be no more than 1/16”.

5.If the difference is greater or less than 1/16” loosen the set screw holding the motor drive pulley to the shaft and adjust the pulley’s position on the shaft until the A1 and A2 measurements are within 1/16” of each other.

6.Tighten the motor drive pulley set screw. See Parts manual for torque specifications.

7.Visually inspect the motor drive pulley to verify that it is perpen- dicular to the drive motor shaft. Points B1 and B2 of Figure should appear to be equal. If they are not, loosen the setscrew of the motor drive pulley and equalize B1 and B2, using care not to disturb the belt alignment performed in step 2.

8.Retighten the motor drive pulley setscrew. See Parts manual for torque specifications.

9.Reinstall belt guard.

Air Compressor Pump Intake and Exhaust Valves

Once a year have a Trained Service Technician check the air compressor pump intake and exhaust valves.

Inspect Air Lines and Fittings for Leaks

1.Turn air compressor off, lock out the power supply, and relieve all air pressure from the air tank.

2.Apply a soap solution to all air line fittings and connections/pip- ing.

3.Correct any leaks found.

IMPORTANT: Even minor leaks can cause the air compressor to over- work, resulting in premature break- down or inadequate performance.

Air compressor Head Bolts - Torquing

The air compressor pump head bolts should be kept properly torqued. Check the torques of the head bolts after the first five hours of operation. Retighten if necessary. See Parts manual for torque specifications.

19-ENG

D26161

Image 19
Contents Instructio N M Anual Safety Guidelines Definitions Hazard Attachments & Accessories Hazard What can Happen HOW to Prevent IT Fire, Inhalation, Damage to Vehicle Surfaces Duty Cycle SpecificationsAccessories GlossaryTo Add Oil To Pump AssemblyTools Required for Assembly UnpackingLocation of the Air Compressor InstallationAnchoring of the Air Compressor Air Distribution System Wiring InstructionsTypical Compressed AIR Distribution System Know Your Air Compressor Description of Operation OperationBefore Starting Break-in Procedure How to Use Your UnitHow to Stop Before Each Start-Up How to StartTo Check Safety Valve MaintenanceCustomer Responsibilities Changing To Drain TankOil CheckingBelt Replacement Air Filter Inspection and ReplacementAdjusting Belt Tension Air compressor Head Bolts Torquing Motor Pulley/Flywheel AlignmentAir Compressor Pump Intake and Exhaust Valves Inspect Air Lines and Fittings for LeaksTo Replace or Clean Check Valve Service and AdjustmentsStorage Additional ServiceMotor Problem Cause Correction TroubleshootingPressure reading Minal box area 25-ENG D26161 AIR Compressor Diagram KEY Part Number Description Parts ListPump Diagram Not Shown Limited Warranty

DLKC6580V2-1 specifications

The Delta DLKC6580V2-1 is an advanced industrial AC servo drive designed to deliver exceptional performance and efficiency in a wide range of automation applications. This servo drive is engineered to enhance system responsiveness while ensuring precise motion control, making it an ideal choice for industries such as manufacturing, packaging, and robotics.

One of the standout features of the DLKC6580V2-1 is its high-speed communication capabilities. The drive supports various communication protocols including EtherCAT, CANopen, and Modbus RTU, ensuring seamless integration into existing systems. This flexibility allows users to connect multiple drives in a network, facilitating coordinated motion control and optimizing the performance of complex machinery.

The DLKC6580V2-1 boasts a powerful control algorithm that provides excellent torque performance and dynamic response. The drive utilizes advanced PWM (Pulse Width Modulation) technology, allowing for smooth operation across a broad range of speeds. This results in minimizing vibrations and improving the overall lifespan of connected servo motors.

In terms of ease of use, the DLKC6580V2-1 features an intuitive user interface with built-in diagnostics and monitoring capabilities. This user-friendly design allows operators to configure parameters swiftly, monitor real-time performance, and troubleshoot any issues effectively. Additionally, it supports maintenance-free operation, significantly reducing downtime and operational costs.

Safety is a priority with the DLKC6580V2-1, which includes multiple safety features like over-voltage, over-current, and temperature protection. The drive is also compliant with international safety standards, ensuring it can be deployed in various environments without compromising personnel safety.

Moreover, the DLKC6580V2-1 is designed to operate efficiently across a wide range of temperatures, making it suitable for different working conditions. Its robust construction ensures reliability and durability, which is crucial for demanding industrial applications.

In conclusion, the Delta DLKC6580V2-1 AC servo drive is a high-performance solution that combines advanced control technology, versatile communication options, and user-friendly features. Its robust safety measures and adaptability to varying operational conditions make it an essential component for enhancing automation in modern industrial setups. Whether for precision machining or complex automation processes, the DLKC6580V2-1 stands as a reliable choice for engineers and manufacturers aiming to optimize their production capabilities.