Campbell Hausfeld NB0064 specifications Nailer Components And Specifications, AIR Inlet 1/4 NPT

Page 2

Operating Instructions

Model NB0064

General Safety Information (Continued)

Read and understand tool labels and manual. Failure to follow warn- ings, dangers, and cau- tions could result in DEATH or SERIOUS INJURY.

Do not use any type

of reactive gases, including, but not lim-

ited to, oxygen and O CO2 combustible gases, as

a power source. Use

filtered, lubricated, regulated com- pressed air only. Use of a reactive gas instead of compressed air may cause the nailer to explode which will cause death or serious personal injury.

Use only a pressure- regulated compressed

air source to limit the air pressure supplied to the tool. The regu-

lated pressure must

not exceed 110 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The nailer could explode which will cause death or serious personal injury.

Never use gasoline

or other flammable liquids to clean the nailer. Never use the

nailer in the presence

of flammable liquids or gases. Vapors could ignite by a spark and

cause an explosion which will result in death or serious personal injury.

Always remain in

a firmly balanced position when using or handling the nailer.

Do not remove, tamper with, or

otherwise cause the Work Contact Element (WCE) or trigger to become

inoperable. Do not operate any tool which has been modified in a like fashion. Death or serious personal injury could result.

Do not touch the

trigger unless dri- ving nails. Never attach air line to

nailer or carry nailer while

touching the trigger. The tool could eject a fastener which will result in death or serious personal injury.

Warning indicates

! WARNING a potentially hazardous situation which, if not avoid- ed, COULD result in death or

serious injury.

Always discon-

nect the tool

from the power source when unattended, performing any

maintenance or repair, clearing a jam, or moving the tool to a new

location. Always reconnect the air line BEFORE loading any fasteners. Do not load the tool with fasteners when either the trigger is depressed or the Work Contact Element (WCE) is engaged. The nailer could eject a fastener causing death or serious personal injury.

Always fit tool with a fitting

or hose cou- pling on or

near the tool in such a manner

that all compressed air in the tool is discharged at the time the fitting or hose coupling is disconnected. Do not use a check valve or any other fit- ting which allows air to remain in the nailer. Death or serious personal injury could occur.

Never place hands or any other body parts in the nail discharge area of the nailer. The nailer might eject a fastener and could result in

death or serious personal injury.

Never carry the nailer by the air

hose or pull the hose to move the

nailer or a com- pressor. Keep hoses away from

heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool dam- age could occur.

Nailer Components And Specifications

Adjustable Exhaust

REQUIRES: 1.7 SCFM with 10 nails per minute @ 90 psi

AIR INLET: 1/4” NPT

NAIL SIZE RANGE: 1” to 2-1/2”

MAGAZINE CAPACITY:

100 Nails per load, 16 gauge

WEIGHT: 3 lbs., 14 oz.

LENGTH: 12-1/2”

HEIGHT: 11”

MAXIMUM PRESSURE: 110 psi

PRESSURE RANGE: 70 - 110 psi

Depth Adjustment

Wheel

Quick Clear Catch

No-Mar Tip

Warning Labels (top and back side)

 

Pusher

 

 

 

Nail Loading

 

 

Slot

Trigger

Magazine

No-Mar tip

Work

Storage

 

(back side)

Contact

 

 

 

Element (WCE)

 

 

www.chpower.com

2

Image 2
Contents Description Table of ContentsGeneral Safety Information Nail Size Range 1 to 2-1/2 Nailer Components And SpecificationsAIR Inlet 1/4 NPT Magazine CapacityLubrication Operating The NailerRecommended Hookup Recommended Hookup Operational ModeSingle Cycle Mode Work Contact Element WCENailer Repair Fastener And Replacement PartsTechnical Support Interchange Information Assembly Procedure For SealsFasteners Troubleshooting Guide Problem Cause SolutionLimited Warranty NB0064Modèle NB0064 Table des MatièresGénéralités sur la Sécurité Capacité DU Chargeur Généralités sur la Sécurité SuitePièces Détachées et Spécifications de la Cloueuse Graissage Branchement RecommandéUtilisation de la Cloueuse Branchement Recommandé Utilisation de la Cloueuse SuiteDéblocage DE LA Cloueuse Ajustement DE LA Direction D’ÉCHAPPEMENTRéglage DE Pénétration DES Clous FonctionnerAttaches Problème Cause Solution Guide de DépannageGarantie Limitée Informaciones Generales de Seguridad ÍndiceDescripción Modelo NB0064Componentes y Especificaciones de la Clavadora Conexión Recomendada Precaucion Ésto leCómo usar la Clavadora LubricacionAdvertencia cer Precaucion ChequeelCómo usar la Cómo Ajustar LA Penetración DEL Clavo Advertencia UnaPara Cargar Y Descargar LA Clavadora Para Ajustar LA Direccion DEL Tubo DE EscapeClavos y Refacciones Servicio TécnicoPara reparar la clavadora Para colocarle los sellosProblema Causa Solución Guía de Diagnóstico de AveríasGarantía Limitada