RIDGID Table Saw manual Motor Specifications and Electrical Requirements

Page 12

Motor Specifications and Electrical Requirements (continued)

A temporary adapter may be used to con- nect this plug to a 2-prong outlet as shown if a properly grounded three prong outlet is not available. This temporary adapter should be used only until a prop- erly grounded three prong outlet can be installed by a qualified electrician. The green colored rigid ear, lug or the like, extending from the adapter must be con- nected to a permanent ground such as a properly grounded outlet box.

Improper connection of the equipment- grounding conductor can result in a risk of electric shock. The conductor with insula- tion having an outer surface that is green with or without yellow stripes is the equip- ment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment- grounding conductor to a live terminal.

If the grounding instructions are not com- pletely understood, or if you are in doubt as to whether the tool is properly grounded check with a qualified electri- cian or service personnel.

WARNING: If not properly grounded, this tool can cause an electrical shock, particularly when used in damp locations, in proximity to plumbing, or out of doors. If an electrical shock occurs there is the potential of a secondary hazard, such as your hands contacting the sawblade.

Properly	3-Prong Plug
Grounded
3-Prong Outlet
	Grounding
	Prong

Make sure this Is Connected

Grounding Lugto a Known Ground

3-Prong Plug

2-Prong Outlet

Adapter

NOTE: The adapter illustrated is for use only if you already have a properly grounded 2-prong outlet.

NOTE: In Canada the use of a temporary adapter is not permitted by the Canadian Electrical Code.

12

Image 12

Contents Page Table of Contents Safety Instructions For Table Saw Before Using The SawReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect your saw Inspect Your Blade Inspect your work areaSafety Instructions For Table Saws Dress for safetyPlan your work Inspect your workpieceReduce the Risk of Accidental Starting Keep Children AwayDon’t Force Tool Before freeing jammed materialTo reduce the risk of throwback of cut off pieces To remove loose pieces beneath or trapped inside the guardBefore Leaving The Saw Before StartingGlossary of Terms for Woodworking While CuttingPush Stick Push BlockRabbet ResinMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Wire Sizes Thermal Overload ProtectorThermal Overload Device Extension Gauge Cord LengthUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Key Switch Table...provides working surface to support workpiecesSawdust Ejection Port Wrench/Blade Storage Rip Fence StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter GaugeAlignment Tools NeededRemove Foam Motor Support Checking Table InsertTo check for parallelism Marked ToothSawbladeCombination Miter Gauge Square GrooveAlignment Checking Blade Tilt, or Squareness of Blade to Table To Check For Squareness, 90 PositionIf blade is square to table Square Blade Pointer at Position StopscrewTo check for alignment, 45 Position If blade is 45 to tableScale Screws Stopscrew Adjusting Rip Fence Guide Bars Aligning Rip Fence Guide BarsPages Rip Scale Hold Down Rip Fence Alignment Adjustment Aligning Sliding Table ExtensionCombination Square Rip Fence Lock Lever Adjustment Adjusting Rip IndicatorAdjusting Nut Rip IndicatorInstalling Blade Guard If the sliding table extension moves when lockedChecking Sliding Table Extension Hex Locking Front Hex Nut CouplingAligning Blade Guard WoodKerf Spreader Blade Do not loosen other screws. ThisRemoving and Installing Sawblade Miter Gauge Alignment Adjusting Bevel Lock Marking Ind-I-Cut UsingMarking the Ind-I-Cut Blade Tilt Lock NutWorkbench Mounting Using Hardware Table Saw Mounting ProceduresFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your SawWorkbench Mounting Using C Clamps Supporting Table Saw with SawhorsesSafety Instructions for Basic Saw Operations Before Each Use Inspect your sawPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Stick Push Block For Use with Auxiliary FenceAuxiliary Fence Fence Facing Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations CrosscuttingRepetitive Crosscutting Clamp Wood Block Cut Off PieceMiter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsWhile Thru sawing Ripping Once the trailing end is on the tableBlade Path Bevel Ripping Narrow Work Auxiliary Fence ClampPush Block Workpiece Auxiliary Fence Baffle Using Featherboards for Thru Sawing Might otherwise pinch the bladeKerf and cause a kickback PushUsing Featherboards for Non-Thru Sawing Install blade guard immediately Using Carbide Tipped BladesResawing KickbackDadoing Dado InsertSaw ArborRabbeting Ploughing and MoldingMolding Molding Auxiliary FenceMaintenance Adjusting Nylon Set ScrewMaintaining Your Table Saw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë Troubleshooting GeneralTrouble Probable Cause Remedy Motor Trouble Probable Cause RemedyRepair Parts Parts List for Ridgid 10 Inch Table Saw Model No. TS24001Always Order by Part Number not by Key Number Key DescriptionRepair Parts Parts List for Ridgid 10 Inch Table Saw Model TS24001 Key Description 827483 Cover BladeMiter Gauge Assembly Always Order by Part Number Not by Key Number DescriptionFence Assembly Guard Assembly Page Page Page RIDGID, INC Stock No. TS2400 Model No. TS24001 Serial No