RIDGID manual Mounting Your Saw, Mounting Table Saw to Workbench or Legset

Page 33

Mounting Your Saw

Mounting Table Saw to Workbench or Legset

WARNING: To reduce the risk of injury from accidental start, make sure switch is "OFF" and plug is not connected to power source outlet.

WARNING: To reduce the risk of injury from kickback or saw movement the saw must be properly secured to a sturdy workbench, cabinet or legset. Casters if provided on the cabi- net or legset must be locked during saw operation. If there is any tendency for the saw to move or rock during operation, this must be corrected immedi- ately.

If table saw is to be used in a permanent location, it should be fastened securely to a firm supporting surface such as a work- bench, or legset using the mounting holes.

Workbench Surface

4"

16-3/4"

3/8"

Dia.

Opening if

15-5/16"

Vacuum

is not used

21-5/16"

3"

23-3/4"

(Front of Table Saw)

Diagram of Workbench Mounting Holes

Workbench Mounting Using Hardware

When mounting table saw to a workbench and using a vacuum hookup, holes should be drilled through the supporting surface of the workbench using the dimensions illustrated.

If a vacuum is not used, an opening must be made in the workbench using the dimensions illustrated, so the sawdust can fall away from the saw base area.

Table Saw Mounting Procedures

1.Locate the proper hole mounting dia- gram for your desired type of table saw mounting.

2.Mark the hole locations and cutout opening if vacuum is not used. Drill the holes and cut out the area to allow saw- dust to fall away from the base if a vac- uum is not being utilized.

3.Place the table saw on the mounting surface and align the four holes.

4.Insert four (4) 1/4-20 screws that are long enough for washers and nuts which will properly secure the table saw to the mounting surface.

NOTE: Mounting hardware (bolts, nuts, washers etc.) are not supplied with the saw.

33

Image 33

Contents Page Table of Contents Before Using The Saw Safety Instructions For Table SawReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect your saw Inspect your work area Inspect Your BladeDress for safety Safety Instructions For Table SawsPlan your work Inspect your workpieceKeep Children Away Reduce the Risk of Accidental StartingDon’t Force Tool Before freeing jammed materialTo remove loose pieces beneath or trapped inside the guard To reduce the risk of throwback of cut off piecesBefore Leaving The Saw Before StartingWhile Cutting Glossary of Terms for WoodworkingPush Block Push StickRabbet ResinMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Thermal Overload Protector Wire SizesThermal Overload Device Extension Gauge Cord LengthUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key SwitchSawdust Ejection Port Rip Fence Storage Wrench/Blade StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter GaugeTools Needed AlignmentRemove Foam Motor Support Checking Table InsertMarked ToothSawblade To check for parallelismCombination Miter Gauge Square GrooveAlignment To Check For Squareness, 90 Position Checking Blade Tilt, or Squareness of Blade to TableIf blade is square to table Square Blade Pointer at Position StopscrewTo check for alignment, 45 Position If blade is 45 to tableScale Screws Stopscrew Adjusting Rip Fence Guide Bars Aligning Rip Fence Guide BarsPages Rip Scale Hold Down Rip Fence Alignment Adjustment Aligning Sliding Table ExtensionCombination Square Adjusting Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Nut Rip IndicatorIf the sliding table extension moves when locked Installing Blade GuardChecking Sliding Table Extension Hex Locking Front Hex Nut CouplingWood Aligning Blade GuardKerf Spreader Blade Do not loosen other screws. ThisRemoving and Installing Sawblade Miter Gauge Alignment Marking Ind-I-Cut Using Adjusting Bevel LockMarking the Ind-I-Cut Blade Tilt Lock NutTable Saw Mounting Procedures Workbench Mounting Using HardwareFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your SawSupporting Table Saw with Sawhorses Workbench Mounting Using C ClampsBefore Each Use Inspect your saw Safety Instructions for Basic Saw OperationsPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push StickAuxiliary Fence Fence Facing Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations CrosscuttingClamp Wood Block Cut Off Piece Repetitive CrosscuttingMiter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsWhile Thru sawing Ripping Once the trailing end is on the tableBlade Path Bevel Ripping Narrow Work Auxiliary Fence ClampPush Block Workpiece Auxiliary Fence Baffle Might otherwise pinch the blade Using Featherboards for Thru SawingKerf and cause a kickback PushUsing Featherboards for Non-Thru Sawing Using Carbide Tipped Blades Install blade guard immediatelyResawing KickbackDado InsertSaw Arbor DadoingPloughing and Molding RabbetingMolding Auxiliary Fence MoldingMaintenance Adjusting Nylon Set ScrewMaintaining Your Table Saw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë Troubleshooting GeneralTrouble Probable Cause Remedy Trouble Probable Cause Remedy MotorParts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair PartsKey Description Always Order by Part Number not by Key NumberRepair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001Always Order by Part Number Not by Key Number Description Miter Gauge AssemblyFence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC