RIDGID Table Saw manual Fence Assembly

Page 63

Repair Parts

Parts List for RIDGID 10 Inch Table Saw

Model No. TS24001

RIDGID parts are available on-line at www.ridgidparts.com

Figure 4 - Fence Assembly

1

										2
										3
										4
					26					6 5
										7
			25							8
24										9
24
23					10
23
1
					11
					11
					12				13
										28
						14				28
20					15					27
20										27
22		20						16
21								16
21					17
					17
		17	19		18

Always Order by Part Number - not by Key Number

Key	Part No.	Description
No.


–	830421	Fence Complete

1809492-5 Screw Pan Hd. Ty “T” 8-32x1

2824350-1 Cap Channel Rear

3820129 * Nut Lock 5/16-18

4274865 * Washer 21/64 x 5/8 x 1/16

59416390 * Screw Pan Hd. Ty “T”

		10-32 x 5/8
6	824328-1	Plate Lock
7	824332	Spring Lock

8824349-1 Slide Rear Fence

9824342-1 Rod Fence Lock

10 827507 Housing Rip Fence

11 9422329 * Scr Hex Hd TY “T”

1/4-20 x 3/4

12809372-3 * Screw Pan 10-32 x 1/2

1360136 * Washer 13/64 x 5/8 x 1/32

14830281 Indicator

15830426 Head Rip Fence

16827532 Slide Fence Head

Key	Part No.	Description
No.

17809169-3 * Screw Pan Hd. Ty “T”

8-32 x 3/8

18822138-1 * Nut Sq 10-32

1962636 * Nut Sq 1/4-20

20824326 Bearing Ball Angular Contact

21830425 Lever Cam Fence

22	824329	Pin Cam
23	827876	Label RIDGID

24828173 * Screw Hex Washer Hd. 1/4-20 x 3/4

25824330-1 Plate Fence Channel

26829971-10 Channel Fence

27806752-2 Screw Pan Hd Ty “T”

10-32 x 1-1/4

28829706 Micro Adjust Asm

Hardware for Attaching Wood Facing 159653-3 Bolt Sq. Hd. 1/4-20 x 3/4 805552 * Washer 17/64 x 5/8 x 1/16 115120 * Nut Hex 1/4-20

* Standard Hardware Item - May be purchased locally

63

Image 63

Contents Page Table of Contents Before Using The Saw Safety Instructions For Table SawReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect your saw Inspect your work area Inspect Your BladeInspect your workpiece Safety Instructions For Table SawsDress for safety Plan your workBefore freeing jammed material Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolBefore Starting To reduce the risk of throwback of cut off piecesTo remove loose pieces beneath or trapped inside the guard Before Leaving The SawWhile Cutting Glossary of Terms for WoodworkingResin Push StickPush Block RabbetMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Extension Gauge Cord Length Wire SizesThermal Overload Protector Thermal Overload DeviceUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key SwitchSawdust Ejection Port Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Wrench/Blade StorageRip Fence Storage Miter Gauge StorageChecking Table Insert AlignmentTools Needed Remove Foam Motor SupportSquare Groove To check for parallelismMarked ToothSawblade Combination Miter GaugeAlignment Square Blade Pointer at Position Stopscrew Checking Blade Tilt, or Squareness of Blade to TableTo Check For Squareness, 90 Position If blade is square to tableTo check for alignment, 45 Position If blade is 45 to tableScale Screws Stopscrew Adjusting Rip Fence Guide Bars Aligning Rip Fence Guide BarsPages Rip Scale Hold Down Rip Fence Alignment Adjustment Aligning Sliding Table ExtensionCombination Square Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Rip Indicator Adjusting NutHex Locking Front Hex Nut Coupling Installing Blade GuardIf the sliding table extension moves when locked Checking Sliding Table ExtensionDo not loosen other screws. This Aligning Blade GuardWood Kerf Spreader BladeRemoving and Installing Sawblade Miter Gauge Alignment Blade Tilt Lock Nut Adjusting Bevel LockMarking Ind-I-Cut Using Marking the Ind-I-CutMounting Your Saw Workbench Mounting Using HardwareTable Saw Mounting Procedures Front of Table Saw Diagram of Workbench Mounting HolesSupporting Table Saw with Sawhorses Workbench Mounting Using C ClampsBefore Each Use Inspect your saw Safety Instructions for Basic Saw OperationsPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push StickAuxiliary Fence Fence Facing Crosscutting Using the Miter GaugeAdditional Safety Instructions for Crosscutting Basic Saw OperationsClamp Wood Block Cut Off Piece Repetitive CrosscuttingMiter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsWhile Thru sawing Ripping Once the trailing end is on the tableBlade Path Bevel Ripping Narrow Work Auxiliary Fence ClampPush Block Workpiece Auxiliary Fence Baffle Push Using Featherboards for Thru SawingMight otherwise pinch the blade Kerf and cause a kickbackUsing Featherboards for Non-Thru Sawing Kickback Install blade guard immediatelyUsing Carbide Tipped Blades ResawingDado InsertSaw Arbor DadoingPloughing and Molding RabbetingMolding Auxiliary Fence MoldingMaintenance Adjusting Nylon Set ScrewMaintaining Your Table Saw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë Troubleshooting GeneralTrouble Probable Cause Remedy Trouble Probable Cause Remedy MotorParts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair PartsKey Description Always Order by Part Number not by Key NumberRepair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001Always Order by Part Number Not by Key Number Description Miter Gauge AssemblyFence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC